101691-4130 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016914130 1156002480

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101691-4130 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101691-4130 1016914130

ISUZU 1156002480 1156002480

Service parts 101691-4130 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101069-1910

3. GOVERNOR 105470-0700

4. SUPPLY PUMP

5. AUTOM. ADVANCE MECHANIS 105612-0830

6. COUPLING PLATE 105662-0350

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-2010

11. Nozzle and Holder 9-15300-184-2

12. Open Pre:MPa(Kqf/cm2) 9.8{100}

13. NOZZLE-HOLDER 105031-2600

14. NOZZLE

105000-1130

15. NOZZLE SET

Include in #1:

101691-4130 as INJECTION-PUMP ASSEMBLY

Include in #2:

104745-8020 as _

Cross reference number

ZEXEL 101691-4130 1016914130

ISUZU 1156002480 1156002480

Zexel num

Bosch num

Firm num

Name

101691-4130
101691-4210

1156002480 ISUZU

INJECTION-PUMP ASSEMBLY
DH100 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle holder 105031-2480

Bosch type code KB69SD273NP6

Opening pressure MPa 9.8

Opening pressure kgf/cm2 100

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 2.2 2.15 2.25

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 13

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 117.5 115.2 119.8

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 13

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 124 120.3 127.7

Max. variation between cylinders % 0 -3 3

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 6.5+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 175 172.7 177.3

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Timer adjustment

Pump speed r/min 400+-50

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 600

Advance angle deg. 0.6 0.1 1.1

Timer adjustment_03

Pump speed r/min 900

Advance angle deg. 1.4 0.9 1.9

Timer adjustment_04

Pump speed r/min 1150

Advance angle deg. 2 1.5 2.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Set the load lever's stop position so that R = aa (N = 0). (3)RACK LIMIT: RAL
----------
DL=6-0.2mm aa=6mm RAL=13+0.2mm
----------

0000000901

F:Full load I:Idle S:Stop
----------

----------
a=6deg+-5deg b=6deg+-5deg c=46deg+-3deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=275r/min Ra=6.5mm
----------