101642-9000 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016429000


101642-9000 INJECTION-PUMP ASSEMBLY
Rating:
67
Buy INJECTION-PUMP ASSEMBLY 101642-9000 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101642-9000 1016429000

Service parts 101642-9000 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101064-9040
3. GOVERNOR 105410-8470
4. SUPPLY PUMP 105220-4860
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156636-6520
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105141-1800
11. Nozzle and Holder 16600-90019
12. Open Pre:MPa(Kqf/cm2) 9.8{100}
13. NOZZLE-HOLDER 105071-1240
14. NOZZLE 105000-1010
15. NOZZLE SET

Include in #1:

101642-9000 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101642-9000 1016429000


Zexel num
Bosch num
Firm num
Name
101642-9000 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   2.3 2.25 2.35
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.1
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   45.2 44.1 46.3
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   6.7+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   8 6.9 9.1
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 

Test data Ex:

Governor adjustment

Test data 101642-9000
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Rack difference between N = N1 and N = N2 (3)Idle sub spring setting: L1.
----------
K=10 N1=750r/min N2=450r/min L1=6.1-0.2mm
----------

Speed control lever angle

Test data 101642-9000
F:Full speed I:Idle (1)Set the pump speed at aa (2)Set the pump speed at bb.
----------
aa=900r/min bb=750r/min
----------
a=29deg+-5deg b=4deg+-5deg c=7deg+-5deg

Stop lever angle

Test data 101642-9000
N:Pump normal S:Stop the pump.
----------

----------
a=19deg+-5deg b=53deg+-5deg

0000001501 GOV FULL LOAD ADJUSTMENT

Test data 101642-9000
Title1:Full load stopper adjustment Title2:Governor set speed LABEL1:Distinguishing LABEL2:Pump speed (r/min) LABEL3:Ave. injection quantity (mm3/st) LABEL4:Max. var. bet. cyl. LABEL5:Remarks LABEL6:Distinguishing LABEL7:Governor set speed (r/min) LABEL8:Remarks (1)Adjustment conditions are the same as those for measuring injection quantity. (2)-
----------

----------
a1=A a2=- r1=750r/min r2=- Q1=45.2+-1.1mm3/st Q2=- c1=+-2.5% c2=- a3=18 a4=15 r3=900r/min r4=750r/min

Timing setting

Test data 101642-9000
(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=24deg
----------
a=(130deg)




Have questions with 101642-9000?





Group cross 101642-9000 ZEXEL

101642-9000  
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 615 939 
1671290116 
INJECTION-PUMP ASSEMBLY
SD33T
Back to top