101609-9221 ZEXEL 9 400 615 922 BOSCH INJECTION-PUMP ASSEMBLY 9400615922 1016099221 3436501051


101609-9221 INJECTION-PUMP ASSEMBLY
Rating:
58
Buy INJECTION-PUMP ASSEMBLY 101609-9221 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 922 9400615922
ZEXEL 101609-9221 1016099221
MITSUBISHI-HEAV 3436501051 3436501051

Service parts 101609-9221 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101062-8561
3. GOVERNOR 105412-2501
4. SUPPLY PUMP 105220-6430
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156643-6520
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105119-4000
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2)
13. NOZZLE-HOLDER 105048-4480
14. NOZZLE 105017-3310
15. NOZZLE SET

Include in #1:

101609-9221 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 615 922 9400615922
ZEXEL 101609-9221 1016099221
MITSUBISHI-HEAV 3436501051 3436501051


Zexel num
Bosch num
Firm num
Name
101609-9221 
101609-9222 
9 400 615 922 
3436501051  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S6K-T * K 14BE PE6A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5720
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.7 3.65 3.75
Rack position
After adjusting injection quantity.
  R=A
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   6.9
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   38.7 37.7 39.7
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   6.4+-0.5
Pump speed r/min   425 425 425
Average injection quantity mm3/st.   8 6.7 9.3
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 

Test data Ex:

Governor adjustment

Test data 101609-9221
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring (4)Main spring setting (5)Set the torque spring. (6)Rack difference between N = N1 and N = N2
----------
K=(15) N1=1100r/min N2=700r/min
----------

Speed control lever angle

Test data 101609-9221
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(21deg)+-5deg b=(22deg)+-5deg

Stop lever angle

Test data 101609-9221
N:Pump normal S:Stop the pump. (1)Hold the boss against the stop side (2)Use the hole at R = aa
----------
aa=60mm
----------
a=53deg+-5deg b=26.5deg+-5deg c=(9deg)

0000001501 I/P WITH LOAD PLUNGER ADJ

Load plunger-equipped pump adjustment 1. Adjust the variation between cylinders and the injection quantity. 2. At Full point A, adjust the pre-stroke to the specified value. 3. After pre-stroke adjustment, reconfirm that the fuel injection quantity and the variation between cylinders is as specified.
----------

----------

Timing setting

Test data 101609-9221
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)After adjusting the injection quantity, adjust at rack position bb.
----------
aa=6deg bb=6.9mm
----------
a=(110deg)




Have questions with 101609-9221?





Group cross 101609-9221 ZEXEL

Mitsubishi-Heav 

 
3436501050 
INJECTION-PUMP ASSEMBLY
S6K-T
101609-9221  

101609-9222 
9 400 615 922 
3436501051 
INJECTION-PUMP ASSEMBLY
S6K-T
 
3436501052 
INJECTION-PUMP ASSEMBLY
S6K-T
F 019 Z20 041 
3436501053 
INJECTION-PUMP ASSEMBLY
S6K-T
 
3436501054 
INJECTION-PUMP ASSEMBLY
S6K-T
Back to top