101609-9193 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016099193 3436501033


101609-9193 INJECTION-PUMP ASSEMBLY
Rating:
52
Buy INJECTION-PUMP ASSEMBLY 101609-9193 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101609-9193 1016099193
MITSUBISHI-HEAV 3436501033 3436501033

Cross reference number

ZEXEL 101609-9193 1016099193
MITSUBISHI-HEAV 3436501033 3436501033


Zexel num
Bosch num
Firm num
Name
101609-9193 
 
3436501033  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S6K-T K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5720
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.7 3.65 3.75
Rack position
After adjusting injection quantity.
  R=A
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   8.6
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   72 71 73
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the lever   *
Boost pressure kPa   85.3 85.3
Boost pressure mmHg   640 640
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.2+-0.5
Pump speed r/min   425 425 425
Average injection quantity mm3/st.   12 10.7 13.3
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Boost compensator adjustment
Pump speed r/min   700 700 700
Rack position   8.95
Boost pressure kPa   33.3 30.6 36
Boost pressure mmHg   250 230 270
Boost compensator adjustment_02
Pump speed r/min   700 700 700
Rack position   9.6
Boost pressure kPa   72 72 72
Boost pressure mmHg   540 540 540

Test data Ex:

Governor adjustment

Test data 101609-9193
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke (4)Rack difference between N = N1 and N = N2
----------
K=14 N1=1100r/min N2=700r/min
----------

Speed control lever angle

Test data 101609-9193
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=70mm
----------
a=15deg+-5deg b=23deg+-5deg

Stop lever angle

Test data 101609-9193
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Speed = bb, rack position = cc (sealed at delivery) (3)Normal
----------
aa=25mm bb=0r/min cc=1-0.5mm
----------
a=21deg+-5deg b=(55deg)

0000001501 I/P WITH LOAD PLUNGER ADJ

Load plunger-equipped pump adjustment 1. Adjust the variation between cylinders and the injection quantity. 2. At Full point A, adjust the pre-stroke to the specified value. 3. After pre-stroke adjustment, reconfirm that the fuel injection quantity and the variation between cylinders is as specified.
----------

----------

Timing setting

Test data 101609-9193
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)After adjusting the injection quantity, adjust at rack position bb.
----------
aa=6deg bb=8.6mm
----------
a=(110deg)




Have questions with 101609-9193?





Group cross 101609-9193 ZEXEL

Dpico 

F 019 Z20 037 
 
INJECTION-PUMP ASSEMBLY
DB58TI

Mitsubishi-Heav 

9 400 612 369 
3436106010 
INJECTION-PUMP ASSEMBLY
S6K-T
9 400 612 037 
3436105080 
INJECTION-PUMP ASSEMBLY
S6K

Dpico 

F 019 Z20 038 
 
INJECTION-PUMP ASSEMBLY
DB58TI
F 019 Z20 039 
 
INJECTION-PUMP ASSEMBLY
DB58T

Mitsubishi-Heav 

9 400 612 211 
3436115070 
INJECTION-PUMP ASSEMBLY
S6K-T
9 400 612 695 
3436128030 
INJECTION-PUMP ASSEMBLY
S6K
9 400 612 696 
 
INJECTION-PUMP ASSEMBLY
9 400 612 803 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi-Heav 

9 400 612 950 
3436501010 
INJECTION-PUMP ASSEMBLY
S6K-T
9 400 615 919 
3436501011 
INJECTION-PUMP ASSEMBLY
S6K-T
9 400 612 697 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi-Heav 

9 400 612 804 
3436106040 
INJECTION-PUMP ASSEMBLY
S6K-T
 
3436501030 
INJECTION-PUMP ASSEMBLY
S6K
9 400 615 920 
3436501031 
INJECTION-PUMP ASSEMBLY
S6K
F 019 Z20 040 
3436501032 
INJECTION-PUMP ASSEMBLY
S6K-T
101609-9193  
 
3436501033 
INJECTION-PUMP ASSEMBLY
S6K-T
Back to top