101609-3230 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016093230


101609-3230 INJECTION-PUMP ASSEMBLY
Rating:
60
Buy INJECTION-PUMP ASSEMBLY 101609-3230 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101609-3230 1016093230

Service parts 101609-3230 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101062-9000
3. GOVERNOR 105404-5080
4. SUPPLY PUMP 105220-5610
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER
14. NOZZLE
15. NOZZLE SET

Include in #1:

101609-3230 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101609-3230 1016093230


Zexel num
Bosch num
Firm num
Name
101609-3230 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-3420
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   2.5 2.45 2.55
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   9.6
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   91 90 92
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Boost pressure kPa   30.7 30.7
Boost pressure mmHg   230 230
Hydraulic cylinder ON   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.1+-0.5
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   15 14 16
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Hydraulic cylinder ON   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   D
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   70 70 80
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Hydraulic cylinder OFF   *
Rack limit   *
Boost compensator adjustment
Pump speed r/min   675 675 675
Rack position   R1-0.7
Boost pressure kPa   8 6.7 9.3
Boost pressure mmHg   60 50 70
Boost compensator adjustment_02
Pump speed r/min   675 675 675
Rack position   R1(9.6)
Boost pressure kPa   17.3 17.3 17.3
Boost pressure mmHg   130 130 130

Test data Ex:

Governor adjustment

Test data 101609-3230
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)The torque control spring does not operate. (4)Adjust the secondary timing before adjusting the governor. (5)RACK LIMIT (When hydraulic cylinder is OFF) (6)Boost compensator stroke: BCL (7)When hydraulic cylinder ON: P1
----------
K=15 BCL=0.7+-0.1mm P1=((392)kPa,(4)kgf/cm2)
----------

Speed control lever angle

Test data 101609-3230
F:Full speed I:Idle S:Stop
----------

----------
a=13deg+-3deg b=27deg+-5deg c=32deg+-3deg

Stop lever angle

Test data 101609-3230
N:Pump normal S:Stop the pump.
----------

----------
a=0deg+-5deg b=53deg+-5deg

Timing setting

Test data 101609-3230
(1)Pump vertical direction (2)Key groove position at No. 1 cylinder's beginning of injection position (at BTDC: aa). (3)Position of the key groove of the No. 1 cylinder at B.T.D.C. bb (fix the governor flyweight at this position for delivery). (4)B.T.D.C.: aa (5)At second timing adjustment, set the camshaft at the * position and tighten the flyweight locknut. (6)Align the flyweight's timing gear position with the lockpin groove and then fully tighten the flyweight to the camshaft. (7)Remove the lock pin and adjust the governor. Reinstall the lock pin to fix the flyweight for delivery.
----------
aa=17deg bb=0deg
----------
a=54deg54min+-3deg b=8deg30min+-30min




Have questions with 101609-3230?





Group cross 101609-3230 ZEXEL

Komatsu 

 
6221731340 
INJECTION-PUMP ASSEMBLY
S6D108
 
 
INJECTION-PUMP ASSEMBLY
9 400 610 775 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 611 388 
6221731950 
INJECTION-PUMP ASSEMBLY
S6D108E
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

 
6735711160 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 610 776 
3863536 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 610 776 
6735711161 
INJECTION-PUMP ASSEMBLY
S6D102E
101609-3230  
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

 
6735711140 
INJECTION-PUMP ASSEMBLY
S6D102E
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

 
6735711170 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 610 777 
3863537 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 610 777 
6735711171 
INJECTION-PUMP ASSEMBLY
S6D102E
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 611 607 
3863356 
INJECTION-PUMP ASSEMBLY
SA6D102E
9 400 611 607 
6736711130 
INJECTION-PUMP ASSEMBLY
SA6D102E
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

 
6736711120 
INJECTION-PUMP ASSEMBLY
SA6D102E
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 615 895 
3863538 
INJECTION-PUMP ASSEMBLY
SA6D102E
9 400 615 895 
6736711121 
INJECTION-PUMP ASSEMBLY
SA6D102E
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 613 056 
 
INJECTION-PUMP ASSEMBLY
9 400 613 141 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 613 146 
3863352 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 613 146 
6735711150 
INJECTION-PUMP ASSEMBLY
S6D102E
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 615 896 
3863402 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 615 896 
6735711210 
INJECTION-PUMP ASSEMBLY
S6D102E
9 400 611 662 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 612 368 
3863386 
INJECTION-PUMP ASSEMBLY
6BT-C
Back to top