101608-9551 ZEXEL 9 400 615 878 BOSCH INJECTION-PUMP ASSEMBLY 9400615878 1016089551 16713z6877


101608-9551 INJECTION-PUMP ASSEMBLY
Rating:
64
Buy INJECTION-PUMP ASSEMBLY 101608-9551 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 878 9400615878
ZEXEL 101608-9551 1016089551
NISSAN-DIESEL 16713Z6877 16713z6877

Include in #2:

Cross reference number

BOSCH 9 400 615 878 9400615878
ZEXEL 101608-9551 1016089551
NISSAN-DIESEL 16713Z6877 16713z6877


Zexel num
Bosch num
Firm num
Name
101608-9551 
9 400 615 878 
16713Z6877  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
FE6E K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8260
Bosch type code   9 430 610 133
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   18
Opening pressure kgf/cm2   184
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131425-0420
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.7 3.65 3.75
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.6
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   90 88.4 91.6
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   9.5+-0.5
Pump speed r/min   265 265 265
Average injection quantity mm3/st.   9 7.2 10.8
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.6)
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   90 89 91
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.9
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   95 91 99
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   (R1-0.25 )
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   86.5 82.5 90.5
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   120 120 130
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   (900)
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1080
Advance angle deg.   2 1.5 2.5
Timer adjustment_03
Pump speed r/min   1225
Advance angle deg.   2 1.5 2.5
Timer adjustment_04
Pump speed r/min   1425
Advance angle deg.   6 5.5 6.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101608-9551
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=M44
----------

Speed control lever angle

Test data 101608-9551
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=39mm
----------
a=20deg+-5deg b=42deg+-3deg

Stop lever angle

Test data 101608-9551
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=42mm
----------
a=25deg+-5deg b=40deg+-5deg

0000001501 LEVER

Test data 101608-9551
(a) Speed lever (B) Accelerator lever (C) Accelerator lever stopper bolt 1. Accelerator lever setting method With the speed lever in the idling position, back off the accelerator lever stopper bolt L1 from where it contacts point a. (Back off 1+0.5 turns and set.)
----------
L1=1+0.5mm
----------

Timing setting

Test data 101608-9551
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)




Have questions with 101608-9551?





Group cross 101608-9551 ZEXEL

Dpico 

 
 
INJECTION-PUMP ASSEMBLY
6D16
 
 
INJECTION-PUMP ASSEMBLY
L7

Nissan-Diesel 

9 400 610 770 
16713Z6330 
INJECTION-PUMP ASSEMBLY
FE6B

Dpico 

 
 
INJECTION-PUMP ASSEMBLY
D1146TI
 
 
INJECTION-PUMP ASSEMBLY
D1146TI

Nissan-Diesel 

 
16713Z6804 
INJECTION-PUMP ASSEMBLY
FE6A
9 400 615 877 
16713Z6879 
INJECTION-PUMP ASSEMBLY
FE6A
 
16713Z6808 
INJECTION-PUMP ASSEMBLY
FE6E
101608-9551  
9 400 615 878 
16713Z6877 
INJECTION-PUMP ASSEMBLY
FE6E
 
16713Z6805 
INJECTION-PUMP ASSEMBLY
FE6E
9 400 615 879 
16713Z6876 
INJECTION-PUMP ASSEMBLY
FE6E
9 400 611 521 
16713Z6806 
INJECTION-PUMP ASSEMBLY
MD92

Dpico 

 
 
INJECTION-PUMP ASSEMBLY
L7A
 
 
INJECTION-PUMP ASSEMBLY
L7A
 
 
INJECTION-PUMP ASSEMBLY
L7A

Nissan-Diesel 

F 019 Z10 120 
1671395306 
INJECTION-PUMP ASSEMBLY
NE6TA
9 400 615 880 
1671395315 
INJECTION-PUMP ASSEMBLY
NE6TA
Back to top