101608-6460 ZEXEL 9 400 613 329 BOSCH INJECTION-PUMP ASSEMBLY 9400613329 1016086460


101608-6460 INJECTION-PUMP ASSEMBLY
Rating:
60
Buy INJECTION-PUMP ASSEMBLY 101608-6460 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 613 329 9400613329
ZEXEL 101608-6460 1016086460

Service parts 101608-6460 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-6730
3. GOVERNOR 105411-2530
4. SUPPLY PUMP 105210-5450
5. AUTOM. ADVANCE MECHANIS 105680-5100
6. COUPLING PLATE 105663-1150
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105160-5311
11. Nozzle and Holder ME441294
12. Open Pre:MPa(Kqf/cm2) 17.7{180}
13. NOZZLE-HOLDER 105030-3660
14. NOZZLE 105025-3960
15. NOZZLE SET

Include in #1:

101608-6460 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 613 329 9400613329
ZEXEL 101608-6460 1016086460


Zexel num
Bosch num
Firm num
Name
101608-6460 
101608-6461 
9 400 613 329 
   
INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.5 4.45 4.55
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   11.1
Pump speed r/min   1200 1200 1200
Average injection quantity mm3/st.   103.5 102.5 104.5
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Boost pressure kPa   54.7 54.7
Boost pressure mmHg   410 410
Injection quantity adjustment_02
Adjusting point   -
Rack position   9.1+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   16.5 15 18
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   E
Rack position   11.3++
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   145 145 155
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   400 400 400
Rack position   9.7
Boost pressure kPa   16 13.3 18.7
Boost pressure mmHg   120 100 140
Boost compensator adjustment_02
Pump speed r/min   400 400 400
Rack position   10.8
Boost pressure kPa   41.3 34.6 48
Boost pressure mmHg   310 260 360
Timer adjustment
Pump speed r/min   0
Advance angle deg.   3 2.5 3.5
Load   0/4
Timer adjustment_02
Pump speed r/min   550+50
Advance angle deg.   3 2.5 3.5
Load   0/4
Remarks
Start
 
Timer adjustment_03
Pump speed r/min   650-50
Advance angle deg.   0 0 0
Load   0/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101608-6460
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Boost compensator stroke: BCL (5)Set idle sub-spring (6)Main spring setting
----------
K=14 BCL=1.1+-0.1mm
----------

Speed control lever angle

Test data 101608-6460
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(26.5deg)+-5deg b=(12.5deg)+-5deg

Stop lever angle

Test data 101608-6460
N:Pump normal S:Stop the pump. (1)Normal (2)Pump speed aa and rack position bb (to be sealed at delivery)
----------
aa=0r/min bb=1-0.5mm
----------
a=35deg+-5deg b=(55deg)

0000001501 TAMPER PROOF

Test data 101608-6460
Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2 maximum)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 101608-6460
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(3deg)




Have questions with 101608-6460?





Group cross 101608-6460 ZEXEL

9 400 613 004 
 
INJECTION-PUMP ASSEMBLY
9 400 615 853 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 940 
ME441213 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 619 508 
 
INJECTION-PUMP ASSEMBLY
9 400 619 509 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 615 854 
ME441215 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 619 510 
 
INJECTION-PUMP ASSEMBLY
9 400 619 511 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 615 855 
ME441232 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 613 005 
 
INJECTION-PUMP ASSEMBLY
9 400 619 512 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 613 472 
ME441260 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 612 753 
 
INJECTION-PUMP ASSEMBLY
9 400 612 921 
 
INJECTION-PUMP ASSEMBLY
9 400 613 106 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 296 
 
INJECTION-PUMP ASSEMBLY
6D34TL

Mitsubishi 

F 019 Z10 296 
ME441273 
INJECTION-PUMP ASSEMBLY
6D34TL
F 019 Z10 904 
ME441273 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 619 513 
 
INJECTION-PUMP ASSEMBLY
9 400 613 262 
 
INJECTION-PUMP ASSEMBLY
9 400 613 295 
 
INJECTION-PUMP ASSEMBLY
9 400 613 380 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 023 
ME441286 
INJECTION-PUMP ASSEMBLY
6D16TL
101608-6460  

101608-6461 
9 400 613 329 
 
INJECTION-PUMP ASSEMBLY
9 400 615 856 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 024 
ME441276 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 619 514 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 613 381 
ME441278 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 619 515 
 
INJECTION-PUMP ASSEMBLY
9 400 619 431 
 
INJECTION-PUMP ASSEMBLY
9 400 613 382 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 025 
ME441450 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 619 516 
 
INJECTION-PUMP ASSEMBLY
9 400 613 383 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 026 
ME441451 
INJECTION-PUMP ASSEMBLY
6D16TL
Back to top