101608-6443 ZEXEL F 019 Z10 296 BOSCH INJECTION-PUMP ASSEMBLY f019z10296 1016086443


101608-6443 INJECTION-PUMP ASSEMBLY
Rating:
51
Buy INJECTION-PUMP ASSEMBLY 101608-6443 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 296 f019z10296
ZEXEL 101608-6443 1016086443

Service parts 101608-6443 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101062-9290
3. GOVERNOR 105401-1500
4. SUPPLY PUMP 105220-7110
5. AUTOM. ADVANCE MECHANIS 105676-1320
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-6920
11. Nozzle and Holder ME440837
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105048-3590
14. NOZZLE 105017-3120
15. NOZZLE SET

Include in #1:

101608-6443 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH F 019 Z10 296 f019z10296
ZEXEL 101608-6443 1016086443


Zexel num
Bosch num
Firm num
Name
101608-6443 
F 019 Z10 296 
   
INJECTION-PUMP ASSEMBLY
6D34TL 14BE INJECTION PUMP ASSY PE6A PE
101608-6443 
101608-6444 
F 019 Z10 296 
ME441273  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D34TL * K 14BE INJECTION PUMP ASSY PE6A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.5 3.45 3.55
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.3
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   85.5 84.5 86.5
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Boost pressure kPa   66 66
Boost pressure mmHg   495 495
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.9+-0.5
Pump speed r/min   490 490 490
Average injection quantity mm3/st.   8 6.7 9.3
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   E
Rack position   10.8++
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   70 70 75
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   750 750 750
Rack position   R1-0.8
Boost pressure kPa   28 21.3 34.7
Boost pressure mmHg   210 160 260
Boost compensator adjustment_02
Pump speed r/min   750 750 750
Rack position   R1(10.3)
Boost pressure kPa   56.7 54 59.4
Boost pressure mmHg   425 405 445
Timer adjustment
Pump speed r/min   0
Advance angle deg.   3 2 3
Load   0/4
Timer adjustment_02
Pump speed r/min   650+-25
Advance angle deg.   3 2 3
Load   0/4
Remarks
Start
 
Timer adjustment_03
Pump speed r/min   750+-25
Advance angle deg.   0 0 0
Load   0/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101608-6443
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Torque control stroke: L1 (N = N1 and N = N2 rack difference). (5)Boost compensator stroke: BCL (6)Main spring setting (7)Set idle sub-spring
----------
K=9 L1=0.3+-0.1mm N1=750r/min N2=300r/min BCL=0.8+-0.1mm
----------

Speed control lever angle

Test data 101608-6443
F:Full speed I:Idle S:Stop (1)Base lever only (2)Stopper bolt setting
----------

----------
a=3deg+-5deg b=35deg+-3deg c=15deg+-5deg

Stop lever angle

Test data 101608-6443
N:Pump normal S:Stop the pump. (1)Normal (2)Rack position = aa, speed = bb (stamp at delivery) (3)Use the hole above R = cc
----------
aa=1-0.5mm bb=0r/min cc=25mm
----------
a=21deg+-5deg b=(55deg)

0000001501 TAMPER PROOF

Test data 101608-6443
Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 101608-6443
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=10deg
----------
a=(130deg)




Have questions with 101608-6443?





Group cross 101608-6443 ZEXEL

9 400 612 753 
 
INJECTION-PUMP ASSEMBLY
9 400 612 921 
 
INJECTION-PUMP ASSEMBLY
9 400 613 106 
 
INJECTION-PUMP ASSEMBLY
101608-6443  
F 019 Z10 296 
 
INJECTION-PUMP ASSEMBLY
6D34TL

Mitsubishi 

101608-6443  

101608-6444 
F 019 Z10 296 
ME441273 
INJECTION-PUMP ASSEMBLY
6D34TL
F 019 Z10 904 
ME441273 
INJECTION-PUMP ASSEMBLY
6D34TL
Back to top