101608-1820 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016081820


101608-1820 INJECTION-PUMP ASSEMBLY
Rating:
18
Buy INJECTION-PUMP ASSEMBLY 101608-1820 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101608-1820 1016081820

Service parts 101608-1820 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101061-9801
3. GOVERNOR 105932-2810
4. SUPPLY PUMP 105210-6070
5. AUTOM. ADVANCE MECHANIS 105643-0160
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6030
11. Nozzle and Holder ME035655
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-3900
14. NOZZLE 105015-5700
15. NOZZLE SET

Include in #1:

101608-1820 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101608-1820 1016081820


Zexel num
Bosch num
Firm num
Name
101608-1820 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.3 3.25 3.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   10.8
Pump speed r/min   850 850 850
Each cylinder's injection qty mm3/st.   61 59.2 62.8
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   10.5 9 12
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(10.8)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   61 60 62
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.15
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   69 65 73
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   D
Rack position   R1+0.6
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   62 58 66
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   90 70 110
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   900--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   850
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   900
Advance angle deg.   0.8
Timer adjustment_04
Pump speed r/min   1200
Advance angle deg.   2.6 2.1 3.1
Timer adjustment_05
Pump speed r/min   1500
Advance angle deg.   5.5 5 6
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101608-1820
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=K53
----------

Speed control lever angle

Test data 101608-1820
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=40mm
----------
a=18.5deg+-5deg b=40.5deg+-3deg

Stop lever angle

Test data 101608-1820
N:Engine manufacturer's normal use S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb (non-injection rack position). Confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed cc. Rack position = dd (non-injection rack position). (3)Rack position = approximately ee (speed lever full, speed = ff). (4)Free (at delivery)
----------
aa=1550r/min bb=4.9-0.5mm cc=275r/min dd=(7.4)mm ee=15mm ff=0r/min
----------
a=40.5deg+-5deg b=(29deg) c=17deg+-5deg

0000001501 LEVER

Test data 101608-1820
(A) Idle (B) Full speed (C) Base lever (D) Accelerator lever (E) Accelerator lever delivery position 1. Measure speed lever angle (1)Measure the angle when the accelerator lever (D) contacted the base lever (C) at a.
----------

----------
b=40.5deg+-3deg c=18.5deg+-5deg

Timing setting

Test data 101608-1820
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(1deg)




Have questions with 101608-1820?





Group cross 101608-1820 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
6D16T
9 400 613 376 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 938 
ME078437 
INJECTION-PUMP ASSEMBLY
6D16T
 
ME444578 
INJECTION-PUMP ASSEMBLY
6D16T
101608-1820  
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 615 820 
ME170409 
INJECTION-PUMP ASSEMBLY
6D14
9 400 615 821 
ME219043 
INJECTION-PUMP ASSEMBLY
6D34T
9 400 615 822 
ME219044 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 615 823 
ME170416 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 824 
ME170418 
INJECTION-PUMP ASSEMBLY
6D17-2
9 400 615 825 
ME078435 
INJECTION-PUMP ASSEMBLY
6D16TE
9 400 615 826 
ME170415 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 827 
ME170417 
INJECTION-PUMP ASSEMBLY
6D17-2
Back to top