101606-9120 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016069120 16713z6001

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101606-9120 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101606-9120 1016069120

NISSAN-DIESEL 16713Z6001 16713z6001

Cross reference number

ZEXEL 101606-9120 1016069120

NISSAN-DIESEL 16713Z6001 16713z6001

Zexel num

Bosch num

Firm num

Name

101606-9120
101606-9220

16713Z6001 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
FE6E * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-1420

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.7 3.65 3.75

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 12.1

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 81.9 80.3 83.5

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.5+-0.5

Pump speed r/min 275 275 275

Average injection quantity mm3/st. 9.5 7.7 11.3

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.1)

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 81.9 80.9 82.9

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(12.1)

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 92 88 96

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.2

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 71.4 68.2 74.6

Fixing the lever *

Injection quantity adjustment_06

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 102 102 112

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min (1130)

Advance angle deg. 0 0 0

Remarks
Measure speed (beginning of operation).

Timer adjustment_02

Pump speed r/min 1200

Advance angle deg. 1 0.5 1.5

Timer adjustment_03

Pump speed r/min 1500

Advance angle deg. 5.5 5.2 5.8

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=H55
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Bottom lever
----------
aa=39mm
----------
a=26.5deg+-5deg b=35deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=42mm
----------
a=20deg+-5deg b=40deg+-5deg

0000001501 LEVER

(a) Speed lever (B) Accelerator lever (C) Accelerator lever stopper bolt (D) Full speed side (E) idle side 1. Accelerator lever setting method With speed lever at idle position, from point S contact Back off the accelerator lever stopper bolt L and set. (Turn bolt L turns and set.)
----------

----------
r=36mm L=1+0.5mm