101606-6571 ZEXEL 9 400 615 523 BOSCH INJECTION-PUMP ASSEMBLY 9400615523 1016066571 me076473


101606-6571 INJECTION-PUMP ASSEMBLY
Rating:
65
Buy INJECTION-PUMP ASSEMBLY 101606-6571 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 523 9400615523
ZEXEL 101606-6571 1016066571
MITSUBISHI ME076473 me076473

Service parts 101606-6571 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-9690
3. GOVERNOR 105931-6262
4. SUPPLY PUMP 105210-4700
5. AUTOM. ADVANCE MECHANIS 105643-0540
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6780
11. Nozzle and Holder ME076000
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-3900
14. NOZZLE 105015-6440
15. NOZZLE SET

Include in #1:

101606-6571 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 615 523 9400615523
ZEXEL 101606-6571 1016066571
MITSUBISHI ME076473 me076473


Zexel num
Bosch num
Firm num
Name
101606-6571 
101607-1580 
9 400 615 523 
ME076473  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D16 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.3 3.25 3.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.1
Pump speed r/min   850 850 850
Each cylinder's injection qty mm3/st.   63.7 61.8 65.6
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   D
Rack position   8.7+-0.5
Pump speed r/min   500 500 500
Each cylinder's injection qty mm3/st.   10.2 8.7 11.7
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.1)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   63.7 62.7 64.7
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   C
Rack position   R1+0.2
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   41.7 37.7 45.7
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   73 63 83
Fixing the lever   *
Rack limit   *
Injection quantity adjustment_06
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   10 8.5 11.5
Fixing the rack   *
Remarks
(check)
 
Timer adjustment
Pump speed r/min   900--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   850
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1200
Advance angle deg.   2.7 2.2 3.2
Timer adjustment_04
Pump speed r/min   1500
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101606-6571
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=F47
----------

Speed control lever angle

Test data 101606-6571
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=18.5deg+-5deg b=41deg+-3deg

Stop lever angle

Test data 101606-6571
N:Pump normal S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb and confirm non-injection. (Rack position = cc is non-injection rack position.) (2)After setting the stopper bolt, confirm non-injection at speed dd (non-injection rack position). (3)Rack position = approximately ee. (4)Free (at shipping)
----------
aa=1400r/min bb=6.7-0.5mm cc=(8.3)mm dd=275r/min ee=17.4mm
----------
a=38.5deg+-5deg b=(27deg) c=17deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400r/min Ra=9.2+-0.1mm
----------

Timing setting

Test data 101606-6571
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=14deg
----------
a=(0deg)




Have questions with 101606-6571?





Group cross 101606-6571 ZEXEL

Mitsubishi 

9 400 615 517 
ME070929 
INJECTION-PUMP ASSEMBLY
6D16T
9 400 615 518 
ME076487 
INJECTION-PUMP ASSEMBLY
6D16
 
ME076488 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 519 
ME076489 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 520 
ME076490 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 521 
ME076491 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 522 
ME076492 
INJECTION-PUMP ASSEMBLY
6D16
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

101606-6571  

101607-1580 
9 400 615 523 
ME076473 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 524 
ME076475 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 525 
ME076476 
INJECTION-PUMP ASSEMBLY
6D16
Back to top