101606-6220 ZEXEL 9 400 615 498 BOSCH INJECTION-PUMP ASSEMBLY 9400615498 1016066220 me076007


101606-6220 INJECTION-PUMP ASSEMBLY
Rating:
27
Buy INJECTION-PUMP ASSEMBLY 101606-6220 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 498 9400615498
ZEXEL 101606-6220 1016066220
MITSUBISHI ME076007 me076007

Include in #2:

Cross reference number

BOSCH 9 400 615 498 9400615498
ZEXEL 101606-6220 1016066220
MITSUBISHI ME076007 me076007


Zexel num
Bosch num
Firm num
Name
101606-6220 
101606-6320 
9 400 615 498 
ME076007  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D16 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.3 3.25 3.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.4
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   54.5 52 57
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   D
Rack position   8.7+-0.5
Pump speed r/min   500 500 500
Each cylinder's injection qty mm3/st.   7.6 5.9 9.3
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.4)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   54.5 53.5 55.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.4
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   79.8 75.8 83.8
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1(11.4)
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   48.5 44.5 52.5
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   14.3+-0. 5
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   73 63 83
Fixing the lever   *
Rack limit   *
Injection quantity adjustment_07
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   8.7 7 10.4
Fixing the rack   *
Remarks
(check)
 
Timer adjustment
Pump speed r/min   900--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   850
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1200
Advance angle deg.   2.7 2.2 3.2
Timer adjustment_04
Pump speed r/min   1500
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101606-6220
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT
----------
T1=B07
----------

Speed control lever angle

Test data 101606-6220
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=18.5deg+-5deg b=41deg+-3deg

Stop lever angle

Test data 101606-6220
N:Pump normal S:Stop the pump. (1)Set the stopper bolt at speed = rated point and rack position = aa and confirm non-injection. (2)After setting the stopper bolt , confirm non-injection at pump speed bb. Rack position = cc (non-injection rack position). (3)Rack position = approximately dd (4)Free (at shipping)
----------
aa=6.7mm bb=275r/min cc=(8.3)mm dd=17.4mm
----------
a=38.5deg+-5deg b=(27deg) c=17deg+-5deg

0000001501 ACS

Test data 101606-6220
(A) Housing (B) Snap ring (C) adjusting screw (D) Set screw (E): Push rod (F) Spacer 1. Adjustment of the aneroid compensator (1)Adjust with the (D) set screw so that the clearance between the (A) housing and (B) snap ring is L1. (2)Select the push rod (E) so that the distance from the end surface of the (F) spacer becomes L2. (3)(C) Turn the screw to adjust the beginning of aneroid compensator operation. 2. Adjustment when mounting the governor. (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Adjust using screw C to obtain the performance shown in the graph above. (3)After final adjustment, confirm that the gap between housing (A) and snapring (B) is L3.
----------
N1=1450r/min L1=1.4~1.7mm L2=0.5+-0.5mm L3=(0.1~0.5)mm
----------
Ra=R1+0.4mm Rb=R1-0.8+-0.1mm Pa=94.6+-4kPa(710+-30mmHg) Pb=61.6kPa(462mmHg) Q1=(79.8)+-2cm3/1000st Q2=(52)+-2cm3/1000st

Timing setting

Test data 101606-6220
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(1deg)




Have questions with 101606-6220?





Group cross 101606-6220 ZEXEL

Mitsubishi 

9 400 615 496 
ME076291 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 497 
ME076335 
INJECTION-PUMP ASSEMBLY
6D16
101606-6220  

101606-6320 
9 400 615 498 
ME076007 
INJECTION-PUMP ASSEMBLY
6D16
 
ME076344 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 499 
ME056788 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 500 
ME086578 
INJECTION-PUMP ASSEMBLY
6D31T
9 400 615 501 
ME076346 
INJECTION-PUMP ASSEMBLY
6D14
9 400 615 502 
ME076347 
INJECTION-PUMP ASSEMBLY
6D14
F 01G 09U 04J 
ME076348 
INJECTION-PUMP ASSEMBLY
6D14
9 400 615 503 
ME076349 
INJECTION-PUMP ASSEMBLY
6D14
Back to top