101606-1310 ZEXEL 9 400 615 437 BOSCH INJECTION-PUMP ASSEMBLY 9400615437 1016061310 me056669


101606-1310 INJECTION-PUMP ASSEMBLY
Rating:
20
Buy INJECTION-PUMP ASSEMBLY 101606-1310 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 437 9400615437
ZEXEL 101606-1310 1016061310
MITSUBISHI ME056669 me056669

Service parts 101606-1310 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-4051
3. GOVERNOR 105490-5410
4. SUPPLY PUMP 105210-4790
5. AUTOM. ADVANCE MECHANIS 105614-4100
6. COUPLING PLATE 105662-0590
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6021
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105030-5010
14. NOZZLE 105015-5390
15. NOZZLE SET

Include in #1:

101606-1310 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 615 437 9400615437
ZEXEL 101606-1310 1016061310
MITSUBISHI ME056669 me056669


Zexel num
Bosch num
Firm num
Name
101606-1310 
9 400 615 437 
ME056669  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.5 4.45 4.55
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   9.6
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   112 108.6 115.4
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   8+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   18.5 15.7 21.3
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.6)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   112 111 113
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(9.6)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   113.5 111 116
Difference in delivery mm3/st.   9 9 9
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   140 120 160
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   850--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   800
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1000
Advance angle deg.   0.9 0.4 1.4
Timer adjustment_04
Pump speed r/min   1150
Advance angle deg.   3 2.5 3.5
Timer adjustment_05
Pump speed r/min   -
Advance angle deg.   4 4 5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 101606-1310
N:Pump speed R:Rack position (mm) (1)Excess fuel setting for starting: SXL (2)Damper spring setting: DL
----------
SXL=R1(9.6)+0.2mm DL=6-0.2mm
----------

Speed control lever angle

Test data 101606-1310
F:Full speed
----------

----------
a=10deg+-5deg

0000000901

Test data 101606-1310
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=24deg+-5deg b=29deg+-3deg

Stop lever angle

Test data 101606-1310
N:Pump normal S:Stop the pump. (1)Rack position = aa, stopper bolt setting (2)Rack position bb (3)Free (at delivery)
----------
aa=5.5-0.5mm bb=16mm
----------
a=12.5deg+5deg-7deg b=34deg+-5deg c=(66.5deg)

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=7.3mm
----------

0000001601 ACS

Test data 101606-1310
Aneroid compensator adjustment (1)Adjust the clearance between the aneroid compensator's main body and the push rod to L1. (2)Pump speed N1 at load lever's full position. (3)Screw in the aneroid compensator body to obtain the performance shown in the graph above.
----------
L1=0.1~0.5mm N1=700r/min
----------
Ra=9.6mm Rb=8.7mm P1=(88.8)kPa((666)mmHg) P2=69.3+-0.7kPa(520+-5mmHg) Q1=112+-1cm3/1000st Q2=-

Timing setting

Test data 101606-1310
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 101606-1310?





Group cross 101606-1310 ZEXEL

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 436 
ME047487 
INJECTION-PUMP ASSEMBLY
6D16
 
ME444571 
INJECTION-PUMP ASSEMBLY
6D16
101606-1310  
9 400 615 437 
ME056669 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 438 
ME056641 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 439 
ME056642 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 440 
ME056643 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 441 
ME056644 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 442 
ME056646 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 443 
ME056647 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 444 
ME056648 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 445 
ME056650 
INJECTION-PUMP ASSEMBLY
6D22
Back to top