101603-8420 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016038420 8943955220

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-8420 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-8420 1016038420

ISUZU 8943955220 8943955220

Cross reference number

ZEXEL 101603-8420 1016038420

ISUZU 8943955220 8943955220

Zexel num

Bosch num

Firm num

Name

101603-8420
101603-8421

8943955220 ISUZU

INJECTION-PUMP ASSEMBLY
6HH1-S * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.7 4.65 4.75

Rack position
After adjusting injection quantity. R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 12.9

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 84 82.4 85.6

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point -

Rack position 9.6+-0.5

Pump speed r/min 275 275 275

Average injection quantity mm3/st. 9.4 8.1 10.7

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.9)

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 84 83 85

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.15

Pump speed r/min 1450 1450 1450

Average injection quantity mm3/st. 94.5 91.3 97.7

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.2

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 75 71.8 78.2

Fixing the lever *

Timer adjustment

Pump speed r/min 905--

Advance angle deg. 0 0 0

Load 3/5

Remarks
Start

Timer adjustment_02

Pump speed r/min 855

Advance angle deg. 0.3

Load 3/5

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 1.5 1 2

Load 5/5

Remarks
Measure the actual speed.

Timer adjustment_04

Pump speed r/min 1110

Advance angle deg. 1.5 1 2

Load 3/5

Timer adjustment_05

Pump speed r/min 1450

Advance angle deg. 7 6.5 7.5

Load 5/5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)At delivery (at R = RA, N = N1)
----------
T1=J73 RA=R1(12.9)mm N1=150r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Set the idle side stopper bolt at rack position = bb (at shipping).
----------
aa=43mm bb=R1(12.9)mm
----------
a=11deg+-5deg b=(45deg)+-3deg c=(14deg)

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=45mm
----------
a=12.5deg+-5deg b=40deg+-5deg

0000001501 I/P WITH LOAD PLUNGER ADJ

Plunger assembly number: PL (stamping: ST) 1. Adjustment procedures (1)Insert the pre-stroke adjusting shims L1 for each cylinder. (2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2) (3)At basic point A, adjust so that the pre-stroke is L2. (4)Reconfirm the injection quantity.
----------
PL=131153-9020 ST=A769 L1=1mm L2=4.7+-0.05mm a1=+-14% a2=+-2.5%
----------

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(150deg)