101603-8280 ZEXEL 9 400 613 468 BOSCH INJECTION-PUMP ASSEMBLY 9400613468 1016038280 1156029080


101603-8280 INJECTION-PUMP ASSEMBLY
Rating:
86
Buy INJECTION-PUMP ASSEMBLY 101603-8280 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 613 468 9400613468
ZEXEL 101603-8280 1016038280
ISUZU 1156029080 1156029080

Service parts 101603-8280 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5280
3. GOVERNOR 105921-5681
4. SUPPLY PUMP 105210-5100
5. AUTOM. ADVANCE MECHANIS 105643-0650
6. COUPLING PLATE 105662-1170
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6301
11. Nozzle and Holder 1-15300-263-1
12. Open Pre:MPa(Kqf/cm2) 22.1{225}
13. NOZZLE-HOLDER 105030-4351
14. NOZZLE 105015-8640
15. NOZZLE SET

Include in #1:

101603-8280 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 613 468 9400613468
ZEXEL 101603-8280 1016038280
ISUZU 1156029080 1156029080


Zexel num
Bosch num
Firm num
Name
101603-8280 
9 400 613 468 
1156029080  ISUZU
INJECTION-PUMP ASSEMBLY
6SD1 K 14BF INJECTION PUMP ASSY PE6AD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.7 3.65 3.75
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.9
Pump speed r/min   650 650 650
Average injection quantity mm3/st.   89.8 88.2 91.4
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   290 290 290
Average injection quantity mm3/st.   11.2 9.2 13.2
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.9)
Pump speed r/min   650 650 650
Average injection quantity mm3/st.   89.8 88.8 90.8
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   88 88 93
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   550--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   500
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1250
Advance angle deg.   4 3.5 4.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-8280
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=E43
----------

Speed control lever angle

Test data 101603-8280
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=18deg+-5deg b=36deg+-3deg

Stop lever angle

Test data 101603-8280
N:Pump normal S:Stop the pump.
----------

----------
a=25deg+-5deg b=40deg+-5deg

0000001501 TAMPER PROOF

Test data 101603-8280
1. Set the full load. (1)After governor adjustment (torque cam phase adjustment), move the load lever to increase the full rack position to R1. (2)Set using the screw (A) so that the rack position is as shown above and tighten the locknut. (3)Again set in the correct rack position using the load lever.
----------
R1=0.4mm
----------

Timing setting

Test data 101603-8280
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(40deg)




Have questions with 101603-8280?





Group cross 101603-8280 ZEXEL

Isuzu 

9 400 615 250 
1156029050 
INJECTION-PUMP ASSEMBLY
6SA1
 
1156029000 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156029001 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
8943949140 
INJECTION-PUMP ASSEMBLY
6HE1
9 400 615 251 
8943949141 
INJECTION-PUMP ASSEMBLY
6HE1
 
8943949150 
INJECTION-PUMP ASSEMBLY
6HE1
9 400 615 252 
 
INJECTION-PUMP ASSEMBLY
6HE1

Isuzu 

9 400 615 252 
8943949151 
INJECTION-PUMP ASSEMBLY
6HE1
F 019 Z10 362 
8943937530 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 363 
8943937531 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 253 
8943937532 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 364 
8943942920 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 365 
8943942921 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 254 
8943942922 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 255 
1156029090 
INJECTION-PUMP ASSEMBLY
6BG1-MTC
9 400 615 256 
1156029110 
INJECTION-PUMP ASSEMBLY
6BG1
101603-8280  
9 400 613 468 
1156029080 
INJECTION-PUMP ASSEMBLY
6SD1
 
8943951110 
INJECTION-PUMP ASSEMBLY
6HE1-N
9 400 613 226 
8943951111 
INJECTION-PUMP ASSEMBLY
6HE1-N
Back to top