101603-8270 ZEXEL 9 400 615 256 BOSCH INJECTION-PUMP ASSEMBLY 9400615256 1016038270 1156029110


101603-8270 INJECTION-PUMP ASSEMBLY
Rating:
85
Buy INJECTION-PUMP ASSEMBLY 101603-8270 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 256 9400615256
ZEXEL 101603-8270 1016038270
ISUZU 1156029110 1156029110

Service parts 101603-8270 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-4990
3. GOVERNOR 105931-9830
4. SUPPLY PUMP 105220-5920
5. AUTOM. ADVANCE MECHANIS 105644-0460
6. COUPLING PLATE 105661-0730
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6241
11. Nozzle and Holder 1-15300-142-1
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-3201
14. NOZZLE 105015-5860
15. NOZZLE SET

Include in #1:

101603-8270 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 615 256 9400615256
ZEXEL 101603-8270 1016038270
ISUZU 1156029110 1156029110


Zexel num
Bosch num
Firm num
Name
101603-8270 
9 400 615 256 
1156029110  ISUZU
INJECTION-PUMP ASSEMBLY
6BG1 K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.6 3.55 3.65
Rack position
After adjusting injection quantity.
  R=A
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   10.6
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   54.2 52.6 55.8
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   290 290 290
Average injection quantity mm3/st.   8.4 7.1 9.7
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(10.6)
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   54.2 53.2 55.2
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(10.6)
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   66.8 63.6 70
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   87 87 119
Fixing the lever   *
Timer adjustment
Pump speed r/min   1390--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1340
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1530
Advance angle deg.   3.5 3 4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-8270
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=C78
----------

Speed control lever angle

Test data 101603-8270
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=35mm
----------
a=34deg+-5deg b=35deg+-3deg

Stop lever angle

Test data 101603-8270
N:Pump normal S:Stop the pump.
----------

----------
a=25deg+-5deg b=40deg+-5deg

0000001501 I/P WITH LOAD PLUNGER ADJ

Plunger assembly number: PL (stamping: ST) 1. Adjustment procedures (1)Insert the pre-stroke adjusting shims L1 for each cylinder. (2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2) (3)At basic point A, adjust so that the pre-stroke is L2. (4)Reconfirm the injection quantity.
----------
PL=131154-2520 ST=A267 L1=1mm L2=3.6+-0.05mm a1=+-14% a2=+-2.5%
----------

Timing setting

Test data 101603-8270
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(60deg)




Have questions with 101603-8270?





Group cross 101603-8270 ZEXEL

Isuzu 

9 400 615 250 
1156029050 
INJECTION-PUMP ASSEMBLY
6SA1
 
1156029000 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156029001 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
8943949140 
INJECTION-PUMP ASSEMBLY
6HE1
9 400 615 251 
8943949141 
INJECTION-PUMP ASSEMBLY
6HE1
 
8943949150 
INJECTION-PUMP ASSEMBLY
6HE1
9 400 615 252 
 
INJECTION-PUMP ASSEMBLY
6HE1

Isuzu 

9 400 615 252 
8943949151 
INJECTION-PUMP ASSEMBLY
6HE1
F 019 Z10 362 
8943937530 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 363 
8943937531 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 253 
8943937532 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 364 
8943942920 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
F 019 Z10 365 
8943942921 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 254 
8943942922 
INJECTION-PUMP ASSEMBLY
6HE1-TC1
9 400 615 255 
1156029090 
INJECTION-PUMP ASSEMBLY
6BG1-MTC
101603-8270  
9 400 615 256 
1156029110 
INJECTION-PUMP ASSEMBLY
6BG1
9 400 613 468 
1156029080 
INJECTION-PUMP ASSEMBLY
6SD1
 
8943951110 
INJECTION-PUMP ASSEMBLY
6HE1-N
9 400 613 226 
8943951111 
INJECTION-PUMP ASSEMBLY
6HE1-N
Back to top