101603-7850 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016037850 8943934610

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-7850 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-7850 1016037850

ISUZU 8943934610 8943934610

Cross reference number

ZEXEL 101603-7850 1016037850

ISUZU 8943934610 8943934610

Zexel num

Bosch num

Firm num

Name

101603-7850
101603-7851

8943934610 ISUZU

INJECTION-PUMP ASSEMBLY
6HE1-S * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 11.5

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 77.7 76.1 79.3

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.5+-0.5

Pump speed r/min 265 265 265

Average injection quantity mm3/st. 8.8 7.5 10.1

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.5)

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 77.7 76.7 78.7

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.2

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 90.7 86.7 94.7

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.2

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 61.8 58.6 65

Fixing the lever *

Injection quantity adjustment_06

Adjusting point I

Rack position -

Pump speed r/min 150 150 150

Average injection quantity mm3/st. 96 96 104

Fixing the lever *

Timer adjustment

Pump speed r/min 1300--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1250

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1500

Advance angle deg. 4 3.5 4.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=G80
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H'
----------
aa=35mm
----------
a=11deg+-5deg b=36deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=45mm
----------
a=12.5deg+-5deg b=40deg+-5deg

0000001501 TAMPER PROOF

1. Set the full load. (1)After governor adjustment (torque cam phase adjustment), move the load lever to increase the full rack position to R1. (2)Set using the screw (A) so that the rack position is as shown above and tighten the locknut. (3)Again set in the correct rack position using the load lever.
----------
R1=0.4mm
----------

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=14deg
----------
a=(150deg)