101603-7433 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016037433 8943968760


101603-7433 INJECTION-PUMP ASSEMBLY
Rating:
48
Buy INJECTION-PUMP ASSEMBLY 101603-7433 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-7433 1016037433
ISUZU 8943968760 8943968760

Service parts 101603-7433 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-4960
3. GOVERNOR 105931-7640
4. SUPPLY PUMP 105210-5110
5. AUTOM. ADVANCE MECHANIS 105643-0620
6. COUPLING PLATE 105661-0781
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-5084
11. Nozzle and Holder 8-94397-483-2
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105048-3862
14. NOZZLE 105017-1090
15. NOZZLE SET

Include in #1:

101603-7433 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101603-7433 1016037433
ISUZU 8943968760 8943968760


Zexel num
Bosch num
Firm num
Name
101603-7433 
 
8943968760  ISUZU
INJECTION-PUMP ASSEMBLY
6HE1-S * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8210
Nozzle   105780-0070
Bosch type code   DN12SD12T-1
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.2 4.15 4.25
Rack position
After adjusting injection quantity.
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.2
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   73.5 71.9 75.1
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   260 260 260
Average injection quantity mm3/st.   8.3 7 9.6
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.2)
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   73.5 72.5 74.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.1
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   84.6 80.6 88.6
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.3
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   55.3 52.1 58.5
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   103 103 135
Fixing the lever   *
Timer adjustment
Pump speed r/min   1210--
Advance angle deg.   0 0 0
Load   3/4
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1160
Advance angle deg.   0.3
Load   3/4
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   5.5 5 6
Load   4/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-7433
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=F10
----------

Speed control lever angle

Test data 101603-7433
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=60mm
----------
a=28.5deg+-5deg b=(36.5deg)+-3deg

Stop lever angle

Test data 101603-7433
N:Pump normal S:Stop the pump.
----------

----------
a=32.5deg+-5deg b=40deg+-5deg

0000001501 I/P WITH LOAD PLUNGER ADJ

Plunger assembly number: PL (stamping: ST) 1. Adjustment procedures (1)Insert the pre-stroke adjusting shims L1 for each cylinder. (2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2) (3)At basic point A, adjust so that the pre-stroke is L2. (4)Reconfirm the injection quantity.
----------
PL=131153-4520 ST=A724 L1=1mm L2=4.2+-0.05mm a1=+-14% a2=+-2.5%
----------

Timing setting

Test data 101603-7433
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)- (5)Pump vertical direction (6)Direction of rotation (7)Pointer (8)Pointer stamping (9)Timing device stamping (10)Timing device (11)Move b deg and stamp both at the same time as shown above. (12)Outside circumference of timing device (13)Secondary timing stamping position for the No. 1 cylinder's beginning of injection
----------
aa=11deg
----------
a=(150deg) b=1deg




Have questions with 101603-7433?





Group cross 101603-7433 ZEXEL

Isuzu 

 
1156026590 
INJECTION-PUMP ASSEMBLY
6SA1
 
1156026591 
INJECTION-PUMP ASSEMBLY
6SA1
9 400 615 179 
1156026592 
INJECTION-PUMP ASSEMBLY
6SA1
 
8943962110 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943962111 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943962112 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943965680 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968700 
INJECTION-PUMP ASSEMBLY
6HE1-S
9 400 615 180 
8943968701 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968702 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968704 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968705 
INJECTION-PUMP ASSEMBLY
6HE1-S
9 400 615 181 
8943968706 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943960311 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943960312 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943965630 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968750 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968751 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968753 
INJECTION-PUMP ASSEMBLY
6HE1-S
9 400 615 182 
8943968754 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943961610 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943961611 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943961612 
INJECTION-PUMP ASSEMBLY
6HE1-S
101603-7433  
 
8943968760 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
1156026521 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156026522 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156026523 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
F 019 Z10 829 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156026524 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
9 400 615 183 
1156026525 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156026531 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156026532 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156026533 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
F 019 Z10 598 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156026534 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
9 400 615 184 
 
INJECTION-PUMP ASSEMBLY
6BG1-TC1

Isuzu 

9 400 615 184 
1156026535 
INJECTION-PUMP ASSEMBLY
6BG1-TC1
 
1156022452 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
8943965690 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968730 
INJECTION-PUMP ASSEMBLY
6HE1-S
F 019 Z10 830 
8943968731 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968733 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943968734 
INJECTION-PUMP ASSEMBLY
6HE1-S
9 400 615 185 
8943968735 
INJECTION-PUMP ASSEMBLY
6HE1-S
 
8943965710 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
8943965711 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
8943965712 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
8943965714 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
8943965715 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
8943965716 
INJECTION-PUMP ASSEMBLY
6HE1-N
9 400 615 186 
 
INJECTION-PUMP ASSEMBLY
6HE1-N

Isuzu 

9 400 615 186 
8943965717 
INJECTION-PUMP ASSEMBLY
6HE1-N
 
1156026730 
INJECTION-PUMP ASSEMBLY
6BG1-TC2
 
1156026731 
INJECTION-PUMP ASSEMBLY
6BG1-TC2
 
1156026732 
INJECTION-PUMP ASSEMBLY
6BG1-TC2
 
1156026733 
INJECTION-PUMP ASSEMBLY
6BG1-TC2
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 615 187 
1156026734 
INJECTION-PUMP ASSEMBLY
6BG1-TC2
Back to top