101603-2663 ZEXEL 9 400 611 327 BOSCH INJECTION-PUMP ASSEMBLY 9400611327 1016032663 220205660a


101603-2663 INJECTION-PUMP ASSEMBLY
Rating:
22
Buy INJECTION-PUMP ASSEMBLY 101603-2663 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 327 9400611327
ZEXEL 101603-2663 1016032663
HINO 220205660A 220205660a

Service parts 101603-2663 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5431
3. GOVERNOR 105401-1112
4. SUPPLY PUMP 105210-4351
5. AUTOM. ADVANCE MECHANIS 105672-0470
6. COUPLING PLATE 105662-1160
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105160-4100
11. Nozzle and Holder 23600-2710A
12. Open Pre:MPa(Kqf/cm2) 17.7{180}
13. NOZZLE-HOLDER 105030-4440
14. NOZZLE 105015-9220
15. NOZZLE SET

Include in #1:

101603-2663 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 611 327 9400611327
ZEXEL 101603-2663 1016032663
HINO 220205660A 220205660a


Zexel num
Bosch num
Firm num
Name
101603-2663 
9 400 611 327 
220205660A  HINO
INJECTION-PUMP ASSEMBLY
H07C-T K 14BF INJECTION PUMP ASSY PE6AD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   134424-0920
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   4.8 4.77 4.83
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   A
Rack position   9.6
Pump speed r/min   1050 1050 1050
Average injection quantity mm3/st.   109 107 111
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the lever   *
Boost pressure kPa   36 36
Boost pressure mmHg   270 270
Injection quantity adjustment_02
Adjusting point   -
Rack position   6.2+-0.5
Pump speed r/min   360 360 360
Average injection quantity mm3/st.   10 9 11
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   130 130 140
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   800 800 800
Rack position   R1-1.45
Boost pressure kPa   5.3 4 6.6
Boost pressure mmHg   40 30 50
Boost compensator adjustment_02
Pump speed r/min   800 800 800
Rack position   R1(9.6)
Boost pressure kPa   22.7 16 29.4
Boost pressure mmHg   170 120 220
Timer adjustment
Pump speed r/min   900--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   850
Advance angle deg.   0.3
Timer adjustment_03
Pump speed r/min   1050
Advance angle deg.   1.5 1.2 1.8
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-2663
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Main spring setting (5)Set idle sub-spring (6)Boost compensator stroke
----------
K=6
----------

Speed control lever angle

Test data 101603-2663
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=125.4mm
----------
a=14deg+-5deg b=21deg+-5deg

Stop lever angle

Test data 101603-2663
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Normal
----------
aa=0r/min bb=1-0.5mm
----------
a=21deg+-5deg b=(55deg)

0000001501 TAMPER PROOF

Test data 101603-2663
Tamperproofing-equipped boost compensator cover installation procedure (A): After adjusting the boost compensator, assemble then tighten the bolts to remove the heads. (B): Specified torque (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 101603-2663
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(50deg)




Have questions with 101603-2663?





Group cross 101603-2663 ZEXEL

Hino 

F 019 Z20 468 
220401410A 
INJECTION-PUMP ASSEMBLY
J-2
F 019 Z20 469 
220401411A 
INJECTION-PUMP ASSEMBLY
J-2
9 400 615 058 
220401412A 
INJECTION-PUMP ASSEMBLY
J-2
 
220401430A 
INJECTION-PUMP ASSEMBLY
J-2
9 400 611 597 
220401431A 
INJECTION-PUMP ASSEMBLY
J-2
F 01G 09U 045 
220401432A 
INJECTION-PUMP ASSEMBLY
J-2
9 400 619 847 
220401310A 
INJECTION-PUMP ASSEMBLY
J-2
F 01G 09U 1BH 
220401311A 
INJECTION-PUMP ASSEMBLY
J-2
 
220205510A 
INJECTION-PUMP ASSEMBLY
H07C-TE
9 400 611 698 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 611 993 
220205510B 
INJECTION-PUMP ASSEMBLY
H07C-TE
 
220205620A 
INJECTION-PUMP ASSEMBLY
H07C-T
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 615 059 
220205620B 
INJECTION-PUMP ASSEMBLY
H07C-T
9 400 611 256 
220205650A 
INJECTION-PUMP ASSEMBLY
H07C-T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Hino 

101603-2663  
9 400 611 327 
220205660A 
INJECTION-PUMP ASSEMBLY
H07C-T
9 400 613 102 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 612 495 
220205680A 
INJECTION-PUMP ASSEMBLY
H07C-T
9 400 615 060 
220205750A 
INJECTION-PUMP ASSEMBLY
H07C-T
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 611 219 
220205740A 
INJECTION-PUMP ASSEMBLY
W06E
9 400 611 219 
S220205740 
INJECTION-PUMP ASSEMBLY
W06E
Back to top