101602-7422 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016027422 1156027152

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101602-7422 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101602-7422 1016027422

ISUZU 1156027152 1156027152

Service parts 101602-7422 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101061-8460

3. GOVERNOR 105419-1020

4. SUPPLY PUMP 105220-5860

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156637-3120

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-6691

11. Nozzle and Holder 1-15300-293-1

12. Open Pre:MPa(Kqf/cm2) 18.1{185}

13. NOZZLE-HOLDER 105030-4361

14. NOZZLE 105015-7070

15. NOZZLE SET

Include in #1:

101401-0631 as _

101602-7422 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101602-7422 1016027422

ISUZU 1156027152 1156027152

Zexel num

Bosch num

Firm num

Name

101602-7422
101602-7423

1156027152 ISUZU

INJECTION-PUMP ASSEMBLY
6BB1 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 8.1

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 53 51.5 54.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 6.2+-0.5

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 7.5 6.2 8.8

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Idle spring not operating. (3)RACK LIMIT: RAL (4)Set idle sub-spring (5)Main spring setting
----------
K=6 RAL=9+0.5mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(2deg)+-5deg b=(15deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=12deg+-5deg b=46deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=20deg
----------
a=(90deg)