101602-7280 ZEXEL 9 400 614 888 BOSCH INJECTION-PUMP ASSEMBLY 9400614888 1016027280 1156025970


101602-7280 INJECTION-PUMP ASSEMBLY
Rating:
10
Buy INJECTION-PUMP ASSEMBLY 101602-7280 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 614 888 9400614888
ZEXEL 101602-7280 1016027280
ISUZU 1156025970 1156025970

Service parts 101602-7280 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101061-8170
3. GOVERNOR 105419-0250
4. SUPPLY PUMP 105220-4781
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156636-9020
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-5053
11. Nozzle and Holder 1-15300-105-2
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-3201
14. NOZZLE 105015-4190
15. NOZZLE SET

Include in #1:

101602-7280 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 614 888 9400614888
ZEXEL 101602-7280 1016027280
ISUZU 1156025970 1156025970


Zexel num
Bosch num
Firm num
Name
101602-7280 
9 400 614 888 
1156025970  ISUZU
INJECTION-PUMP ASSEMBLY
6BD1-TQF * K 14BE PE6A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.4 3.35 3.45
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   8.5
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   74.3 72.3 76.3
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   8.1
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   77 75.5 78.5
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   5.2+-0.5
Pump speed r/min   325 325 325
Average injection quantity mm3/st.   12.1 10.8 13.4
Max. variation between cylinders %   0 -14 14
Fixing the rack   *

Test data Ex:

Governor adjustment

Test data 101602-7280
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring (4)Main spring setting
----------
K=17
----------

Speed control lever angle

Test data 101602-7280
F:Full speed I:Idle D:Dead point (1)Stopper bolt setting
----------

----------
a=18deg+-1deg b=20deg+-3deg c=29deg+-5deg

Stop lever angle

Test data 101602-7280
N:Pump normal S:Stop the pump. (1)Normal
----------

----------
a=2.5deg+-5deg b=46deg+-5deg

0000001501 LEVER

Test data 101602-7280
1. Variable lever adjustment (1)Fix lever B in the idle position using the bolts C and D. (2)Temporarily fix lever A in center of long hole. (3)Set the dead point position temporarily and measure the lever angle. (4)After idle adjustment, loosen the full side stopper bolt D. (5)Move lever A in full speed direction. (6)Fix the bolt D at the full speed position. (7)Fix lever A using bolt E. (8)(G) Lock using bolt. (9)Finally, measure the lever angle and set the idle stopper bolt (C) stop position.
----------

----------

Timing setting

Test data 101602-7280
(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(100deg)




Have questions with 101602-7280?





Group cross 101602-7280 ZEXEL

Isuzu 

9 400 614 883 
1156024940 
INJECTION-PUMP ASSEMBLY
6BG1-TPB
9 400 614 884 
1156024950 
INJECTION-PUMP ASSEMBLY
6BG1
9 400 619 720 
1156025480 
INJECTION-PUMP ASSEMBLY
6BG1-T
 
1156025490 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 614 885 
1156025620 
INJECTION-PUMP ASSEMBLY
6BB1
9 400 614 886 
1156025790 
INJECTION-PUMP ASSEMBLY
6BD1-T
9 400 614 887 
1156025630 
INJECTION-PUMP ASSEMBLY
6BD1
 
1156025880 
INJECTION-PUMP ASSEMBLY
6BB1
101602-7280  
9 400 614 888 
1156025970 
INJECTION-PUMP ASSEMBLY
6BD1-TQF
 
1156026220 
INJECTION-PUMP ASSEMBLY
6BD1
Back to top