101601-8661 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016018661 1156016803


101601-8661 INJECTION-PUMP ASSEMBLY
Rating:
63
Buy INJECTION-PUMP ASSEMBLY 101601-8661 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101601-8661 1016018661
ISUZU 1156016803 1156016803

Service parts 101601-8661 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-2120
3. GOVERNOR 105931-2061
4. SUPPLY PUMP 105220-4781
5. AUTOM. ADVANCE MECHANIS 105612-3250
6. COUPLING PLATE 105661-0661
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-5053
11. Nozzle and Holder 1-15300-105-2
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-3201
14. NOZZLE 105015-4190
15. NOZZLE SET

Include in #1:

101601-8661 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101601-8661 1016018661
ISUZU 1156016803 1156016803


Zexel num
Bosch num
Firm num
Name
101601-8661 
101601-8662 
 
1156016803  ISUZU
INJECTION-PUMP ASSEMBLY
6BD1-T *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.4 3.35 3.45
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   10.6
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   72 70.4 73.6
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   9.6+-0.5
Pump speed r/min   290 290 290
Average injection quantity mm3/st.   9.4 8.1 10.7
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(10.6)
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   72 71 73
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.1
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   76.5 73.3 79.7
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.25
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   46.5 43.3 49.7
Fixing the lever   *
Timer adjustment
Pump speed r/min   1050--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1000
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   (1300)
Advance angle deg.   1 0.5 1.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101601-8661
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT: RAL
----------
T1=B51 RAL=13.5+0.2mm
----------

Speed control lever angle

Test data 101601-8661
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=35mm
----------
a=40deg+-5deg b=32deg+-3deg

Stop lever angle

Test data 101601-8661
N:Pump normal S:Stop the pump.
----------

----------
a=25deg+-5deg b=40deg+-5deg

Timing setting

Test data 101601-8661
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(60deg)




Have questions with 101601-8661?





Group cross 101601-8661 ZEXEL

Isuzu 

 
1156016020 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156016024 
INJECTION-PUMP ASSEMBLY
6BG1
9 400 614 668 
1156016026 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156016200 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156016201 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156016204 
INJECTION-PUMP ASSEMBLY
6BG1
9 400 614 669 
1156016206 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156014300 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014301 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014303 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156016921 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016922 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016923 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016924 
INJECTION-PUMP ASSEMBLY
6BD1T
 
1156016380 
INJECTION-PUMP ASSEMBLY
6BB1
 
1156016790 
INJECTION-PUMP ASSEMBLY
6BD1-T
9 400 610 019 
1156016793 
INJECTION-PUMP ASSEMBLY
6BD1-T
9 400 613 032 
1156016795 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016800 
INJECTION-PUMP ASSEMBLY
6BD1-T
101601-8661  

101601-8662 
 
1156016803 
INJECTION-PUMP ASSEMBLY
6BD1-T
9 400 614 670 
1156016805 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016810 
INJECTION-PUMP ASSEMBLY
6BD1-T
9 400 610 020 
1156016813 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016820 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156016823 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156015150 
INJECTION-PUMP ASSEMBLY
6BD1
 
1156015153 
INJECTION-PUMP ASSEMBLY
6BD1
Back to top