101492-9210 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014929210 3676112010

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101492-9210 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101492-9210 1014929210

MITSUBISHI-HEAV 3676112010 3676112010

Service parts 101492-9210 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101049-9510

3. GOVERNOR 105400-5870

4. SUPPLY PUMP 105220-5751

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-4921

11. Nozzle and Holder 36761-05081

12. Open Pre:MPa(Kqf/cm2) 17.7{180}

13. NOZZLE-HOLDER 105048-3330

14. NOZZLE 105017-0910

15. NOZZLE SET

Include in #1:

101492-9210 as INJECTION-PUMP ASSEMBLY

103682-0543 as _

Cross reference number

ZEXEL 101492-9210 1014929210

MITSUBISHI-HEAV 3676112010 3676112010

Zexel num

Bosch num

Firm num

Name

101492-9210
101492-9220

3676112010 MITSUBISHI-HEAV

INJECTION-PUMP ASSEMBLY
S4F * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-0920

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 9

Pump speed r/min 1250 1250 1250

Average injection quantity mm3/st. 40.6 39.6 41.6

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 9+-0.5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 9.5 8.2 10.8

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 70 70 75

Fixing the lever *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)RACK LIMIT (3)Rack difference between N = N1 and N = N2
----------
K=20 N1=1250r/min N2=700r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(21deg)+-5deg b=(22deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=72deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of key groove at No 1 cylinder's beginning of injection (3)Stamp aligning marks on the pump housing flange. (4)-
----------

----------
a=58deg+-3deg b=4deg+-30min