101491-0530 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014910530 8970251390

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101491-0530 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101491-0530 1014910530

ISUZU 8970251390 8970251390

Cross reference number

ZEXEL 101491-0530 1014910530

ISUZU 8970251390 8970251390

Zexel num

Bosch num

Firm num

Name

101491-0530
101491-0538

8970251390 ISUZU

INJECTION-PUMP ASSEMBLY
4BE1 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.8 3.75 3.85

Rack position
After adjusting injection quantity. R=A

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point -

Rack position 12.3

Pump speed r/min 950 950 950

Average injection quantity mm3/st. 56.5 54.9 58.1

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.5+-0.5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 10 8.7 11.3

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.3)

Pump speed r/min 950 950 950

Average injection quantity mm3/st. 56.5 55.5 57.5

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.35

Pump speed r/min 1750 1750 1750

Average injection quantity mm3/st. 75.8 71.8 79.8

Fixing the lever *

Injection quantity adjustment_05

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 86 70 102

Fixing the lever *

Timer adjustment

Pump speed r/min 1525--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1475

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min 1775

Advance angle deg. 4.5 4 5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)At delivery (at R = A, N = N1)
----------
T1=E97 N1=100r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt set position 'H' (2)Set the idle side stopper bolt at speed = aa and rack position = bb (at delivery)
----------
aa=100r/min bb=R1(12.3)mm
----------
a=(8deg) b=37.5deg+-3deg c=2.5deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa
----------
aa=64mm
----------
a=45deg+-5deg b=29deg+-5deg

0000001501 I/P WITH LOAD PLUNGER ADJ

Plunger assembly number: PL (stamping: ST) 1. Adjustment procedures (1)Insert the pre-stroke adjusting shims L1 for each cylinder. (2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2) (3)At basic point A, adjust so that the pre-stroke is L2. (4)Reconfirm the injection quantity.
----------
PL=131154-1820 ST=A260 L1=1mm L2=3.8+-0.05mm a1=+-14% a2=+-2.5%
----------

0000001601 FICD

1. FICD adjustment (1)FICD adjustment not necessary. (2)Set the clearance between the actuator rod and speed lever to approx. L1.
----------
L1=3+1mm
----------

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=15deg
----------
a=(90deg)