101491-0471 ZEXEL 9 400 614 286 BOSCH INJECTION-PUMP ASSEMBLY 9400614286 1014910471 8943263391

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101491-0471 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 614 286 9400614286

ZEXEL 101491-0471 1014910471

ISUZU 8943263391 8943263391

Service parts 101491-0471 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101049-8510

3. GOVERNOR 105931-5841

4. SUPPLY PUMP 105210-6130

5. AUTOM. ADVANCE MECHANIS 105622-1591

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-6090

11. Nozzle and Holder 8-94114-604-0

12. Open Pre:MPa(Kqf/cm2) 18.1{185}

13. NOZZLE-HOLDER 105031-3940

14. NOZZLE

105015-4740

15. NOZZLE SET

Include in #1:

101402-3521 as _

101491-0471 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 614 286 9400614286

ZEXEL 101491-0471 1014910471

ISUZU 8943263391 8943263391

Zexel num

Bosch num

Firm num

Name

101491-0471

9 400 614 286

8943263391 ISUZU

INJECTION-PUMP ASSEMBLY
4BC2 K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.4 3.35 3.45

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point -

Rack position 10.2

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 49.2 47.6 50.8

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point -

Rack position 9.9+-0.5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 9.5 8 11

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point A

Rack position R1(10.2)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 49.2 48.2 50.2

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1-0.1

Pump speed r/min 1800 1800 1800

Average injection quantity mm3/st. 46.5 43.3 49.7

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1+0.1

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 39.8 36.6 43

Fixing the lever *

Injection quantity adjustment_06

Adjusting point I

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 57.5 52.5 62.5

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 1300--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1250

Advance angle deg. 0.6

Timer adjustment_03

Pump speed r/min 1900

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT
----------
T1=A49
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=5.5deg+-5deg b=37deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=45deg+-5deg b=40deg+-5deg

0000001501 ACS

(A) Set screw (B) Push rod 1 (C) Push rod 2 (D) Cover 1. Aneroid compensator unit adjustment (1)Select the push rod 2 to obtain L2. (2)Screw in (A) to obtain L1. 2. Adjustment when mounting the governor. (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above. (3)As there is hysterisis, measure when the absolute pressure drops. (4)Hysterisis must not exceed rack position = h1.
----------
N1=1100r/min L1=(1.5)mm L2=11+-0.5mm h1=0.15mm
----------
Ra=R1(10.2)mm Rb=(R1-0.4)mm Pa=97.3+-2.7kPa(730+-20mmHg) Pb=79.4kPa(596mmHg) Q1=49.2+-1cm3/1000st Q2=41.1+-1cm3/1000st

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(100deg)