101441-9370 ZEXEL 9 400 610 087 BOSCH INJECTION-PUMP ASSEMBLY 9400610087 1014419370 1670064w01


101441-9370 INJECTION-PUMP ASSEMBLY
Rating:
39
Buy INJECTION-PUMP ASSEMBLY 101441-9370 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 087 9400610087
ZEXEL 101441-9370 1014419370
NISSAN-DIESEL 1670064W01 1670064w01

Service parts 101441-9370 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101044-8190
3. GOVERNOR 105542-4110
4. SUPPLY PUMP 105220-4750
5. AUTOM. ADVANCE MECHANIS 105622-1320
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105141-2490
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 9.8{100}
13. NOZZLE-HOLDER 105071-1271
14. NOZZLE
15. NOZZLE SET

Include in #1:

101441-9370 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH 9 400 610 087 9400610087
ZEXEL 101441-9370 1014419370
NISSAN-DIESEL 1670064W01 1670064w01


Zexel num
Bosch num
Firm num
Name
101441-9370 
9 400 610 087 
1670064W01  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
SD25 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-4-2
Pre-stroke mm   2.3 2.25 2.35
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.3
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   38.3 37.3 39.3
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   8.7+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   8 6.9 9.1
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Timer adjustment
Pump speed r/min   950--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1400
Advance angle deg.   2.1 1.6 2.6
Timer adjustment_04
Pump speed r/min   2030
Advance angle deg.   5.6 5.1 6.1
Timer adjustment_05
Pump speed r/min   -
Advance angle deg.   6 5.5 6.5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 101441-9370
N:Pump speed R:Rack position (mm) P:Negative pressure (1)Pneumatic governor (2)Mechanical governor (3)Acting negative pressure: P1 (4)RACK LIMIT: RAL (5)Beginning of idle sub spring operation: L1 (6)Without stopper disk (7)Injection quantity Q = Q1 or less
----------
RAL=14.7-0.3mm L1=8.7+0.3mm Q1=3mm3/st
----------

Speed control lever angle

Test data 101441-9370
B:When boosted N:Normal S:Stop (1)Rack position = aa (2)Rack position corresponding to cc
----------
aa=0mm bb=15mm
----------
a=26deg+-3deg b=35deg+-5deg c=1deg+-5deg

0000001501 ACS

Test data 101441-9370
(N): Speed of the pump (P): governor's negative pressure (Pa): aneroid compensator's negative pressure (A) rubber boot (B) Nut (c) Nut (D) Lever 1. Aneroid compensator installation (1)Turn nut (C) to adjust gap to L1. (Remove rubber boot at adjustment.) (2)Lock using nut (B). (3)After installation, the lever D must move smoothly when the lever D is moved to the excess fuel side, and R = R1 or more.
----------
L1=0.1~0.5mm R1=16mm
----------
N=1000r/min P=2.94kPa(300mmAq) R1=R1(11.2)mm R2=(R1-0.6)mm R3=(R1-0.8)+-0.2mm R4=(R1-1.2)mm Pa1=1.23kPa(125mmHg) Pa2=1.61kPa(164mmHg) Pa3=2.29kPa(234mmHg)

Timing setting

Test data 101441-9370
(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=15deg
----------
a=(140deg)




Have questions with 101441-9370?





Group cross 101441-9370 ZEXEL

Nissan-Diesel 

 
1670029W06 
INJECTION-PUMP ASSEMBLY
SD25
 
1679090177 
INJECTION-PUMP ASSEMBLY
SD25
 
1670064W00 
INJECTION-PUMP ASSEMBLY
SD25
 
 
INJECTION-PUMP ASSEMBLY
SD23
 
 
INJECTION-PUMP ASSEMBLY
SD23
 
16700V6604 
INJECTION-PUMP ASSEMBLY
SD23
 
16700J1800 
INJECTION-PUMP ASSEMBLY
SD25
 
16700J1801 
INJECTION-PUMP ASSEMBLY
SD25
101441-9370  
9 400 610 087 
1670064W01 
INJECTION-PUMP ASSEMBLY
SD25
 
16700V6605 
INJECTION-PUMP ASSEMBLY
SD23
F 01G 09U 01J 
16700T8278 
INJECTION-PUMP ASSEMBLY
SD25
Back to top