101441-9292 ZEXEL 9 400 614 137 BOSCH INJECTION-PUMP ASSEMBLY 9400614137 1014419292 16700v6603

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101441-9292 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 614 137 9400614137

ZEXEL 101441-9292 1014419292

NISSAN-DIESEL 16700V6603 16700v6603

Service parts 101441-9292 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101044-8140

3. GOVERNOR 105542-4012

4. SUPPLY PUMP

105220-5001

5. AUTOM. ADVANCE MECHANIS 105622-1250

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105141-2130

11. Nozzle and Holder 16600-36W00

12. Open Pre:MPa(Kqf/cm2) 9.8{100}

13. NOZZLE-HOLDER 105071-1271

14. NOZZLE

105000-1740

15. NOZZLE SET

Include in #1:

101441-9292 as INJECTION-PUMP ASSEMBLY

Include in #2:

105856-7143 as _

Cross reference number

BOSCH 9 400 614 137 9400614137

ZEXEL 101441-9292 1014419292

NISSAN-DIESEL 16700V6603 16700v6603

Zexel num

Bosch num

Firm num

Name

101441-9292

9 400 614 137

16700V6603 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
SD23 * K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.3 2.25 2.35

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point -

Rack position 11.5

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 36.1 35.1 37.1

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point -

Rack position 8.1+-0.5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 8 6.9 9.1

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point -

Rack position -

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 36.1 35.6 36.6

Remarks
Set full load.

Timer adjustment

Pump speed r/min 550--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 500

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1200

Advance angle deg. 2 1.5 2.5

Timer adjustment_04

Pump speed r/min 2150

Advance angle deg. 7 6.5 7.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) P:Negative pressure (1)Pneumatic governor (2)Mechanical governor (3)Acting negative pressure: P1 (4)RACK LIMIT: RAL (5)Beginning of idle sub spring operation: L1 (6)Without stopper disk (7)Injection quantity Q = Q1 or less (at N = N1)
----------
P1=2.55+-0.2kPa(260+-20)mmAq RAL=14.7-0.3mm L1=8.1+0.3mm Q1=3mm3/st N1=(2600)r/min
----------

Speed control lever angle

N:Normal B:When boosted S:Stop (1)Rack position = aa (2)Rack position corresponding to cc
----------
aa=0mm bb=15mm
----------
a=2.5deg+-5deg b=23deg+-3deg c=7deg+-5deg

0000001501 ACS

(N): Speed of the pump (P): governor's negative pressure (Pa): aneroid compensator's negative pressure (A) rubber boot (B) Nut (c) Nut (D) Lever 1. Aneroid compensator installation (1)Turn nut (C) to adjust gap to L1. (Remove rubber boot at adjustment.) (2)Lock using nut (B). (3)After installation, the lever D must move smoothly when the lever D is moved to the excess fuel side, and R = R1 or more.
----------
L1=0.1~0.5mm R1=16mm
----------
N=1000r/min P=0.4kPa(40mmAq) Ra=11.5mm Rb=11.45mm Rc=11.05+-0.2mm Pa1=8-5.3kPa(60-40mmHg) Pa2=16.7kPa(125mmHg) Q1=- Q2=-

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(130deg)