101405-9091 ZEXEL 9 400 612 159 BOSCH INJECTION-PUMP ASSEMBLY 9400612159 1014059091 3426104011

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101405-9091 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 612 159 9400612159

ZEXEL 101405-9091 1014059091

MITSUBISHI-HEAV 3426104011 3426104011

Service parts 101405-9091 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101040-4020

3. GOVERNOR 105419-4500

4. SUPPLY PUMP

105220-7180

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-6760

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105048-3330

14. NOZZLE

105017-2760

15. NOZZLE SET

Include in #1:

101405-9091 as INJECTION-PUMP ASSEMBLY

106682-9901 as _

Cross reference number

BOSCH 9 400 612 159 9400612159

ZEXEL 101405-9091 1014059091

MITSUBISHI-HEAV 3426104011 3426104011

Zexel num

Bosch num

Firm num

Name

101405-9091
101405-9092

9 400 612 159

3426104011 MITSUBISHI-HEAV

INJECTION-PUMP ASSEMBLY
S4K-T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-5720

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 9.1

Pump speed r/min 975 975 975

Average injection quantity mm3/st. 92 91 93

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 6+-0.5

Pump speed r/min 425 425 425

Average injection quantity mm3/st. 11.5 10.2 12.8

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position 10++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 105 105 110

Fixing the lever *

Rack limit *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting
----------
K=12
----------

Speed control lever angle

F:Full speed I:Idle S:Stop (1)Base lever only
----------

----------
a=3deg+-5deg b=31deg+-3deg c=17deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Normal (2)Use the hole at R = aa (3)Speed = bb, rack position = cc (sealed at delivery)
----------
aa=23mm bb=0r/min cc=1-0.5mm
----------
a=0deg+-5deg b=(55deg)