101402-0270 ZEXEL F 019 Z10 279 BOSCH INJECTION-PUMP ASSEMBLY f019z10279 1014020270 5156011143

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101402-0270 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 279 f019z10279

ZEXEL 101402-0270 1014020270

ISUZU 5156011143 5156011143

Service parts 101402-0270 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101040-8190

3. GOVERNOR 105410-5920

4. SUPPLY PUMP 105220-4772

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156635-5321

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-4372

11. Nozzle and Holder 5-15300-103-2

12. Open Pre:MPa(Kqf/cm2) 14.7{150}

13. NOZZLE-HOLDER 105030-3391

14. NOZZLE

105015-3930

15. NOZZLE SET

Include in #1:

101402-0270 as INJECTION-PUMP ASSEMBLY

101602-5020 as _

Cross reference number

BOSCH F 019 Z10 279 f019z10279

ZEXEL 101402-0270 1014020270

ISUZU 5156011143 5156011143

Zexel num

Bosch num

Firm num

Name

101402-0270

F 019 Z10 279

5156011143 ISUZU

INJECTION-PUMP ASSEMBLY
4BD1 * K 14BC PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 8.7

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 43.2 42.1 44.3

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point B

Rack position 9.7

Pump speed r/min 725 725 725

Average injection quantity mm3/st. 62.5 60.5 64.5

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 7+-0.5

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 7.2 5.8 8.6

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Set idle sub-spring (3)Main spring setting
----------
K=10
----------

Speed control lever angle

F:Full speed I:Idle (1)When pump speed set at aa (2)When speed set at bb (at shipping).
----------
aa=750r/min bb=900r/min
----------
a=4.5deg+-5deg b=6.5deg+-5deg c=22.5deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=(19deg) b=(34deg)

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(90deg)