101401-7451 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014017451 8971784852

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101401-7451 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101401-7451 1014017451

ISUZU 8971784852 8971784852

Service parts 101401-7451 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-8760

3. GOVERNOR 105932-2622

4. SUPPLY PUMP 105230-1111

5. AUTOM. ADVANCE MECHANIS 105676-8080

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-7340

11. Nozzle and Holder 8-97200-570-0

12. Open Pre:MPa(Kqf/cm2) 18.1{185}/21.1{215}

13. NOZZLE-HOLDER 105048-3831

14. NOZZLE 105017-2310

15. NOZZLE SET

Include in #1:

101401-7451 as INJECTION-PUMP ASSEMBLY

106672-3691 as _

Cross reference number

ZEXEL 101401-7451 1014017451

ISUZU 8971784852 8971784852

Zexel num

Bosch num

Firm num

Name

101401-7451
101401-7452

8971784852 ISUZU

INJECTION-PUMP ASSEMBLY
4HG1-T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8310

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2240

Opening pressure MPa 18

Opening pressure kgf/cm2 184

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-3920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-3-4-2

Pre-stroke mm 3.8 3.75 3.85

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point -

Rack position 11.8

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 54 52.4 55.6

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 8.9+-0.5

Pump speed r/min 315 315 315

Average injection quantity mm3/st. 23 21.7 24.3

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.8)

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 54 53 55

Basic *

Fixing the lever *

Boost pressure kPa 61.3 61.3

Boost pressure mmHg 460 460

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.95

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 56 52 60

Fixing the lever *

Boost pressure kPa 61.3 61.3

Boost pressure mmHg 460 460

Injection quantity adjustment_05

Adjusting point C

Rack position R2-1.2

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 45.7 41.7 49.7

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position R2-1.2

Boost pressure kPa 14 12.7 15.3

Boost pressure mmHg 105 95 115

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position R2(R1-0. 3)

Boost pressure kPa 48 48 48

Boost pressure mmHg 360 360 360

Timer adjustment

Pump speed r/min (N1+50)- -

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min N1

Advance angle deg. 0.5

Remarks
Measure the actual speed.

Timer adjustment_03

Pump speed r/min N2

Advance angle deg. 4 3.5 4.5

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=N40 BCL=1.2+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=43deg+-5deg b=39.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)At pump speed bb and rack position cc, set the stopper bolt.
----------
aa=58mm bb=1500r/min cc=3.5+-0.2mm
----------
a=23deg+-5deg b=(31deg)+-5deg

0000001501 FICD

(A) applied negative pressure (B) Screw (c) Nut 1. Set the actuator as described below. (1)Confirm that there is clearance between the actuator lever and the speed lever. (2)Loosen the nut (C). (3)Push in the screw (B). (4)Apply P1 from the actuator (A) part. (5)Pull out the screw (B) slowly. (6)Tighten and fix the nut (C) when pump speed is Na and the rack position is Ra. (7)Torque the nut (C) to T1. (8)Apply P2 several times. (9)Confirm that the actuator functions normally. (10)Confirm that there is a clearance between the actuator lever and the speed lever at that time.
----------
P1=53.3kPa(400mmHg) P2=53.3kPa(400mmHg) Na=400r/min Ra=8.9+-0.1mm T1=1.2~1.6N-m(0.12~0.16kgf-m)
----------
L=(5)mm

0000001601 RACK SENSOR

Rack sensor adjustment 1. Flange type rack sensor (rack sensor adjustment -5*20) (1)These types of rack sensors do not need adjustment. Confirm the performance with the following procedures. (2)Mount the rack sensor main body to the pump main body. (3)Fix the pump lever at full. (4)At supply voltage V1, pump speed N1 and rack position Ra, confirm that the amp's output voltage is Vist. (5)Move the pump lever two or three times. (6)Set again to full. (7)Confirm that the amplifier output voltage is Vist. (8)Fix the caution plate to the upper part of the rack sensor. (For those without the caution plate instructions, make sure the nameplate of the rack sensor carries the "Don't hold here" caution.) (9)Apply red paint to the rack sensor mounting bolts (2 places).
----------
V1=5+-0.01V N1=1500r/min Ra=R1(11.8)+0.95mm Vist=2.97+-0.28V
----------

Timing setting

(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)Stamping position on the A/T outer rim (4)At the No 1 cylinder's beginning of injection, align with the aligning mark seen through the bracket's check hole and mark the A/T's bevel C1. (5)B.T.D.C.: aa
----------
aa=7deg
----------
a=(60deg) b=(85deg)