101401-4440 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014014440 8970753970


101401-4440 INJECTION-PUMP ASSEMBLY
Rating:
74
Buy INJECTION-PUMP ASSEMBLY 101401-4440 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101401-4440 1014014440
ISUZU 8970753970 8970753970

Cross reference number

ZEXEL 101401-4440 1014014440
ISUZU 8970753970 8970753970


Zexel num
Bosch num
Firm num
Name
101401-4440 
101401-4441 
 
8970753970  ISUZU
INJECTION-PUMP ASSEMBLY
4HF1 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-3-4-2
Pre-stroke mm   4.1 4.05 4.15
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.7
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   62.5 60.9 64.1
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   285 285 285
Average injection quantity mm3/st.   15.5 14.2 16.8
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.7)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   62.5 61.5 63.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.2
Pump speed r/min   1600 1600 1600
Average injection quantity mm3/st.   75.5 71.5 79.5
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   80 80 112
Fixing the lever   *
Timer adjustment
Pump speed r/min   1375--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1325
Advance angle deg.   0.3
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   3.3 2.8 3.8
Timer adjustment_04
Pump speed r/min   1600--
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101401-4440
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=H96
----------

Speed control lever angle

Test data 101401-4440
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=43deg+-5deg b=36deg+-3deg

Stop lever angle

Test data 101401-4440
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa
----------
aa=64mm
----------
a=20deg+-5deg b=29deg+-5deg

0000001501 ACS

Test data 101401-4440
(A) Housing (B) Snap ring (C) adjusting screw (D) Set screw (E): Push rod (F) Spacer 1. Adjustment of the aneroid compensator (1)Adjust with the (D) set screw so that the clearance between the (A) housing and (B) snap ring is L1. (2)Select the push rod (E) so that the distance from the end surface of the (F) spacer becomes L2. (3)(C) Turn the screw to adjust the beginning of aneroid compensator operation. 2. Adjustment when mounting the governor. (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Adjust using screw C to obtain the performance shown in the graph above. (3)After final adjustment, confirm that the gap between housing (A) and snapring (B) is L3.
----------
N1=1100r/min L1=1.4~1.7mm L2=0.5+-0.5mm L3=0.1~0.5mm
----------
Ra=R1(11.7)mm Rb=(R1-0.5)mm Pa=95.4+-2.7kPa(716+-20mmHg) Pb=70.1+-0.7kPa(526+-5mmHg) Q1=62.5+-1cm3/1000st Q2=47.1+-1.6cm3/1000st

Timing setting

Test data 101401-4440
(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)Stamping position on the A/T outer rim (4)Pump bracket check hole position. (5)At the No 1 cylinder's beginning of injection, align with the projection seen through the bracket's check hole and mark the A/T's bevel C1. (6)B.T.D.C.: aa
----------
aa=10deg
----------
a=(60deg) b=(85deg)




Have questions with 101401-4440?





Group cross 101401-4440 ZEXEL

Isuzu 

 
8970613920 
INJECTION-PUMP ASSEMBLY
4HE1-T
 
8970613921 
INJECTION-PUMP ASSEMBLY
4HE1-T
 
8970613923 
INJECTION-PUMP ASSEMBLY
4HE1-T
 
8971140020 
INJECTION-PUMP ASSEMBLY
4HE1-T
 
8971197170 
INJECTION-PUMP ASSEMBLY
4HE1-T
9 400 613 698 
8971295670 
INJECTION-PUMP ASSEMBLY
4HE1-T
 
 
INJECTION-PUMP ASSEMBLY
4BD1
 
8970857010 
INJECTION-PUMP ASSEMBLY
4BD1-T
9 400 613 351 
8970857011 
INJECTION-PUMP ASSEMBLY
4BD1-T
9 400 613 699 
8970829781 
INJECTION-PUMP ASSEMBLY
4BG1
101401-4440  

101401-4441 
 
8970753970 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970753972 
INJECTION-PUMP ASSEMBLY
9 400 613 700 
8971140040 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970753990 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970753991 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970753992 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 701 
8971140050 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 702 
8970903651 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 703 
8970903711 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 704 
8970903631 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 705 
8970903691 
INJECTION-PUMP ASSEMBLY
4HF1
Back to top