101401-4220 ZEXEL F 019 Z10 565 BOSCH INJECTION-PUMP ASSEMBLY f019z10565 1014014220


101401-4220 INJECTION-PUMP ASSEMBLY
Rating:
25
Buy INJECTION-PUMP ASSEMBLY 101401-4220 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 565 f019z10565
ZEXEL 101401-4220 1014014220

Service parts 101401-4220 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101040-8930
3. GOVERNOR 105931-8630
4. SUPPLY PUMP 105210-5160
5. AUTOM. ADVANCE MECHANIS 105676-5020
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-5253
11. Nozzle and Holder 8-97114-015-0
12. Open Pre:MPa(Kqf/cm2) 18.1(185)
13. NOZZLE-HOLDER 105048-3673
14. NOZZLE 105017-1210
15. NOZZLE SET

Include in #1:

101401-4220 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 565 f019z10565
ZEXEL 101401-4220 1014014220


Zexel num
Bosch num
Firm num
Name
101401-4220 
101401-4221 
F 019 Z10 565 
   
INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   134424-3920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-3-4-2
Pre-stroke mm   4.1 4.05 4.15
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.8
Pump speed r/min   960 960 960
Average injection quantity mm3/st.   74.6 73 76.2
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   325 325 325
Average injection quantity mm3/st.   8.7 7.4 10
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.8)
Pump speed r/min   960 960 960
Average injection quantity mm3/st.   74.6 73.6 75.6
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.5
Pump speed r/min   1600 1600 1600
Average injection quantity mm3/st.   93.7 89.7 97.7
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   79 79 111
Fixing the lever   *
Timer adjustment
Pump speed r/min   1375--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1325
Advance angle deg.   0.3
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   3.3 2.8 3.8
Timer adjustment_04
Pump speed r/min   1600--
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101401-4220
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=G31
----------

Speed control lever angle

Test data 101401-4220
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=41deg+-5deg b=(38deg)+-3deg

Stop lever angle

Test data 101401-4220
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa
----------
aa=64mm
----------
a=20deg+-5deg b=29deg+-5deg

0000001501 FICD

Test data 101401-4220
(A) applied negative pressure (B) Screw (c) Nut 1. Set the actuator as described below. (1)Confirm that there is clearance between the actuator lever and the speed lever. (2)Loosen the nut (C). (3)Push in the screw (B). (4)Apply P1 from the actuator (A) part. (5)Pull out the screw (B) slowly. (6)Tighten and fix the nut (C) when pump speed is Na and the rack position is Ra. (7)Torque the nut (C) to T1. (8)Apply P2 several times. (9)Confirm that the actuator functions normally. (10)Confirm that there is a clearance between the actuator lever and the speed lever at that time.
----------
P1=53.3kPa(400mmHg) P2=53.3kPa(400mmHg) Na=410r/min Ra=9.55+-0.1mm T1=1.2~1.6N-m(0.12~0.16kgf-m)
----------
L=(2)mm

Timing setting

Test data 101401-4220
(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)Stamping position on the A/T outer rim (4)Pump bracket check hole position. (5)At the No 1 cylinder's beginning of injection, align with the projection seen through the bracket's check hole and mark the A/T's bevel C1. (6)B.T.D.C.: aa
----------
aa=11deg
----------
a=(60deg) b=(85deg)




Have questions with 101401-4220?





Group cross 101401-4220 ZEXEL

Isuzu 

 
8970432590 
INJECTION-PUMP ASSEMBLY
4BD1
9 400 613 683 
8970432591 
INJECTION-PUMP ASSEMBLY
4BD1
9 400 613 684 
8970440061 
INJECTION-PUMP ASSEMBLY
4BD1
101401-4220  

101401-4221 
F 019 Z10 565 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
8970468730 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 685 
8970468732 
INJECTION-PUMP ASSEMBLY
4HF1
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
8970468740 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 686 
8970468742 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970468340 
INJECTION-PUMP ASSEMBLY
4BD1-T
9 400 611 676 
8970468341 
INJECTION-PUMP ASSEMBLY
4BD1-T
F 019 Z10 804 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

F 019 Z10 466 
8970479570 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 687 
8970479571 
INJECTION-PUMP ASSEMBLY
4HF1
F 019 Z10 805 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

F 019 Z10 467 
8970479580 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 688 
8970479581 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970610270 
INJECTION-PUMP ASSEMBLY
4BD1
 
8970610271 
INJECTION-PUMP ASSEMBLY
4BD1
9 400 612 249 
8970610272 
INJECTION-PUMP ASSEMBLY
4BD1
 
8970610280 
INJECTION-PUMP ASSEMBLY
4BD1-T
 
8970610281 
INJECTION-PUMP ASSEMBLY
4BD1-T
9 400 612 251 
8970610282 
INJECTION-PUMP ASSEMBLY
4BD1-T
 
8970337630 
INJECTION-PUMP ASSEMBLY
4HF1
 
8970337631 
INJECTION-PUMP ASSEMBLY
4HF1
9 400 613 689 
8970337633 
INJECTION-PUMP ASSEMBLY
4HF1
Back to top