101401-2330 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014012330 220204700a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101401-2330 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101401-2330 1014012330

HINO 220204700A 220204700a

Service parts 101401-2330 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-9240

3. GOVERNOR 105401-0820

4. SUPPLY PUMP 105220-5590

5. AUTOM. ADVANCE MECHANIS 105676-1020

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-5070

11. Nozzle and Holder 23600-2010A

12. Open Pre:MPa(Kqf/cm2) 19.6{200}

13. NOZZLE-HOLDER 105041-5110

14. NOZZLE 105015-7650

15. NOZZLE SET

Include in #1:

101401-2330 as INJECTION-PUMP ASSEMBLY

101603-2383 as _

Cross reference number

ZEXEL 101401-2330 1014012330

HINO 220204700A 220204700a

Zexel num

Bosch num

Firm num

Name

101401-2330
101401-2331

220204700A HINO

INJECTION-PUMP ASSEMBLY
W04C-TI * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-0920

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 4.3 4.27 4.33

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.75 90.25

Difference between angles 2
Cal 1-4 deg. 180 179.75 180.25

Difference between angles 3
Cyl.1-2 deg. 270 269.75 270.25

Injection quantity adjustment

Adjusting point A

Rack position 10.5

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 91.5 89.5 93.5

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Boost pressure kPa 50.7 50.7

Boost pressure mmHg 380 380

Injection quantity adjustment_02

Adjusting point C

Rack position 8.4+-0.5

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 10 8.5 11.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 650 650 650

Rack position R1-1.2

Boost pressure kPa 13.3 10.6 16

Boost pressure mmHg 100 80 120

Boost compensator adjustment_02

Pump speed r/min 650 650 650

Rack position R1(10.5)

Boost pressure kPa 37.3 37.3 37.3

Boost pressure mmHg 280 280 280

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Load 1/4

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.3

Load 1/4

Timer adjustment_03

Pump speed r/min (1000)

Advance angle deg. 1.25 0.65 1.25

Load 4/4

Timer adjustment_04

Pump speed r/min 1200

Advance angle deg. 1.25 0.65 1.25

Load 3/4

Timer adjustment_05

Pump speed r/min 1500

Advance angle deg. 4.5 4.2 4.8

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Main spring setting (4)Set idle sub-spring (5)Boost compensator stroke: BCL
----------
K=7 BCL=1.2+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=27deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery)
----------
aa=0r/min bb=1-0.5mm
----------
a=21deg+-5deg b=(55deg)

Timing setting

(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(70deg)