101401-1934 ZEXEL F 019 Z10 923 BOSCH INJECTION-PUMP ASSEMBLY f019z10923 1014011934 me441030


101401-1934 INJECTION-PUMP ASSEMBLY
Rating:
24
Buy INJECTION-PUMP ASSEMBLY 101401-1934 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 923 f019z10923
ZEXEL 101401-1934 1014011934
MITSUBISHI ME441030 me441030

Service parts 101401-1934 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101041-9740
3. GOVERNOR 105401-1490
4. SUPPLY PUMP 105220-6371
5. AUTOM. ADVANCE MECHANIS 105676-1210
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-6920
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105048-3590
14. NOZZLE 105017-3120
15. NOZZLE SET

Include in #1:

101401-1934 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 923 f019z10923
ZEXEL 101401-1934 1014011934
MITSUBISHI ME441030 me441030


Zexel num
Bosch num
Firm num
Name
101401-1934 
101401-1935 
F 019 Z10 923 
ME441030  MITSUBISHI
INJECTION-PUMP ASSEMBLY
4D34TL * K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-4-2
Pre-stroke mm   3.5 3.45 3.55
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.4
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   97.5 96.5 98.5
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Boost pressure kPa   35.3 35.3
Boost pressure mmHg   265 265
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.7+-0.5
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   8 6.7 9.3
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   C
Rack position   10.6++
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   155 155 160
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   800 800 800
Rack position   R1-0.7
Boost pressure kPa   14.7 8 21.4
Boost pressure mmHg   110 60 160
Boost compensator adjustment_02
Pump speed r/min   800 800 800
Rack position   R1(10.4)
Boost pressure kPa   26 23.3 28.7
Boost pressure mmHg   195 175 215
Timer adjustment
Pump speed r/min   0
Advance angle deg.   2.5 2 3
Timer adjustment_02
Pump speed r/min   (630)
Advance angle deg.   2.5 2 3
Remarks
Start
 
Timer adjustment_03
Pump speed r/min   720+-25
Advance angle deg.   0 0 0
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101401-1934
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Boost compensator stroke: BCL
----------
K=12 BCL=0.7+-0.1mm
----------

Speed control lever angle

Test data 101401-1934
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(7deg)+-5deg b=(18deg)+-5deg

Stop lever angle

Test data 101401-1934
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Normal
----------
aa=0r/min bb=4-0.5mm
----------
a=14deg+-5deg b=(48deg)

0000001501 TAMPER PROOF

Test data 101401-1934
Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 101401-1934
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=11deg
----------
a=(130deg)




Have questions with 101401-1934?





Group cross 101401-1934 ZEXEL

9 400 613 415 
 
INJECTION-PUMP ASSEMBLY
9 400 613 416 
 
INJECTION-PUMP ASSEMBLY
9 400 613 173 
 
INJECTION-PUMP ASSEMBLY
9 400 613 350 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

101401-1934  

101401-1935 
F 019 Z10 923 
ME441030 
INJECTION-PUMP ASSEMBLY
4D34TL
F 01G 09U 1CS 
ME444589 
INJECTION-PUMP ASSEMBLY
4D34TL
Back to top