101340-9010 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1013409010 62156000693d


101340-9010 INJECTION-PUMP ASSEMBLY
Rating:
10
Buy INJECTION-PUMP ASSEMBLY 101340-9010 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101340-9010 1013409010
ISEKI 62156000693D 62156000693d

Service parts 101340-9010 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101034-9140
3. GOVERNOR 105419-0280
4. SUPPLY PUMP
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156636-0320
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105151-1451
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 11.8{120}
13. NOZZLE-HOLDER 105081-3141
14. NOZZLE 105000-1650
15. NOZZLE SET

Include in #1:

101340-9010 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101340-9010 1013409010
ISEKI 62156000693D 62156000693d


Zexel num
Bosch num
Firm num
Name
101340-9010 
 
62156000693D  ISEKI
INJECTION-PUMP ASSEMBLY
E3AB1 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-3-2
Pre-stroke mm   1.95 1.9 2
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 2
Cyl.1-2
deg.   240 239.5 240.5
Injection quantity adjustment
Adjusting point   A
Rack position   13.3
Pump speed r/min   1300 1300 1300
Average injection quantity mm3/st.   47.4 46.4 48.4
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   8.2+-0.5
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   8 7 9
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 

Test data Ex:

Governor adjustment

Test data 101340-9010
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK CAP: R1 (3)Set idle sub-spring (4)Main spring setting (5)Rack difference between N = N1 and N = N2
----------
K=7 R1=(17.5)mm N1=1300r/min N2=800r/min
----------

Speed control lever angle

Test data 101340-9010
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=18deg+-5deg b=32deg+-5deg

Stop lever angle

Test data 101340-9010
N:Pump normal S:Stop the pump.
----------

----------
a=23deg+-5deg b=46deg+-5deg

Timing setting

Test data 101340-9010
(1)Pump vertical direction (2)Position of gear mark 'Z' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=22deg
----------
a=(120deg)




Have questions with 101340-9010?





Group cross 101340-9010 ZEXEL

Iseki 

 
62156000692C 
INJECTION-PUMP ASSEMBLY
E3AB1
101340-9010  
 
62156000693D 
INJECTION-PUMP ASSEMBLY
E3AB1
Back to top