101331-9210 ZEXEL 9 400 613 525 BOSCH INJECTION-PUMP ASSEMBLY 9400613525 1013319210 1671316h00


 

Information injection-pump assembly

BOSCH 9 400 613 525 9400613525
ZEXEL 101331-9210 1013319210
NISSAN-DIESEL 1671316H00 1671316h00
101331-9210 INJECTION-PUMP ASSEMBLY
Rating:
86
Buy INJECTION-PUMP ASSEMBLY 101331-9210 zexel genuine, new aftermarket engine parts with delivery

Service parts 101331-9210 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101033-0040
3. GOVERNOR 105931-3871
4. SUPPLY PUMP 105220-4030
5. AUTOM. ADVANCE MECHANIS 105622-0570
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 9.8{100}
13. NOZZLE-HOLDER 105071-1080
14. NOZZLE 105000-1010
15. NOZZLE SET

Include in #1:

101331-9210 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 613 525 9400613525
ZEXEL 101331-9210 1013319210
NISSAN-DIESEL 1671316H00 1671316h00


Zexel num
Bosch num
Firm num
Name
101331-9210 
9 400 613 525 
1671316H00  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
SD15T * K 14BA INJECTION PUMP ASSY PE1A,2A,3A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-2
Pre-stroke mm   2.3 2.25 2.35
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 2
Cyl.1-2
deg.   240 239.5 240.5
Injection quantity adjustment
Adjusting point   -
Rack position   15
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   41.3 39.7 42.9
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   10.1+-0. 5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   7.5 6.4 8.6
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(15)
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   41.3 40.2 42.4
Basic   *
Fixing the lever   *
Boost pressure kPa   60 60
Boost pressure mmHg   450 450
Injection quantity adjustment_04
Adjusting point   B
Rack position   R2(14.25 )
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   34.4 32.4 36.4
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Boost compensator adjustment
Pump speed r/min   700 700 700
Rack position   R1-1
Boost pressure kPa   6.7 4 9.4
Boost pressure mmHg   50 30 70
Boost compensator adjustment_02
Pump speed r/min   700 700 700
Rack position   R1-0.5
Boost pressure kPa   26.7 23.4 30
Boost pressure mmHg   200 175 225
Boost compensator adjustment_03
Pump speed r/min   700 700 700
Rack position   R1(15)
Boost pressure kPa   46.7 46.7 46.7
Boost pressure mmHg   350 350 350
Timer adjustment
Pump speed r/min   550--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   500
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   550
Advance angle deg.   0.7
Timer adjustment_04
Pump speed r/min   1000
Advance angle deg.   2.2 1.7 2.7
Timer adjustment_05
Pump speed r/min   1300
Advance angle deg.   3.9 3.4 4.4
Timer adjustment_06
Pump speed r/min   1400
Advance angle deg.   4.4 3.9 4.9
Timer adjustment_07
Pump speed r/min   -
Advance angle deg.   5 5 5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 101331-9210
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT: RAL (3)Boost compensator stroke: BCL
----------
T1=70 RAL=15.3-0.2mm BCL=1+-0.1mm
----------

Speed control lever angle

Test data 101331-9210
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=5deg+-5deg b=45deg+-3deg

Stop lever angle

Test data 101331-9210
N:Pump normal S:Stop the pump.
----------

----------
a=20deg+-5deg b=40deg+-5deg

Timing setting

Test data 101331-9210
(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(130deg)




Information:

CompactorCB68B (S/N: 496100-100)Asphalt PaverAP1055F (S/N: RLM1-105)AP555F (S/N: 5F51-101)AP600F (S/N: LR61-108)AP655F (S/N: 4801-103; P651-124; ML61-113; 4791-122,125-125)Excavator320D2 (S/N: BW21-235; CY21-192; ZBH1-975,10001-10185)323D2 (S/N: FLC1-219,10001-10004; KCE1-428; JEG1-257; PJP1-1331; YCR1-288; TDT1-560,10001-10135; KBX1-191,10001-10006)326D2 (S/N: REC1-197,199-199,202-203,205-206,208-212; MZH1-282,10001-10006; JFL1-174; XAM1-510,10001-10060; MGW1-313; NBX1-156; KGY1-323)329D2 (S/N: RGA1-309; KJB1-180; SHJ1-190; TMJ1-376; WDT145-145; THW1-506,509-554)330D2 (S/N: PTE1-211; ZBF1-514,10001-10073,10076-10088; RCK1-357; SZK1-561,10001-10143)Generator SetXQP150 (S/N: PJ71-105,107-107,109-112)Motor Grader120L (S/N: E93100-100)120N (S/N: E94100-100; E951-101)Soil Compactor815K (S/N: WCS100-100,201-201)TelehandlerTL1055D (S/N: MNT63-63,150-181,183-186,188-188,192-192)TL1255D (S/N: MYW1-157,160-161,15700-15700)Track-Type TractorD3K2 (S/N: FT31-103,2100-2115,2119-2119; LT31-113,2110-2111)D4K2 (S/N: RT3130-130,2130-2130)D5K2 (S/N: WT31-157,2140-2174; YT31-157,2150-2163,2167-2167)D5R2 (S/N: R5A150-150,152-158,161-162)D6K2 (S/N: MXK1-273; RPR1-307)D6N (S/N: P5T1-166)Vibratory Soil CompactorCS79B (S/N: CM71-101)Wheel Loader924K (S/N: KW41-395; ENC1-1566; HJF1-101,250-818; SNZ100-100,250-430)930K (S/N: DYB1-486; EYE1-127,250-789; FRK1-131,350-433; P3K1-195; TNY1-69)938K (S/N: W8K1-306; REP150-150,450-625; XXT1-137,350-962; HFW1-932)950 GC (S/N: M5K1-1212,1214-1233)950L (S/N: LXX1-228)950M (S/N: ENE1-212,215-234; LCR201-201)962L (S/N: MTN1-163; SXS1-203)962M (S/N: LSE1-208)Wheel Skidder525D (S/N: 2L51-153)535D (S/N: 3L51-136)545D (S/N: 4L51-159)555D (S/N: 5L51-111)Wheeled ExcavatorM315D2 (S/N: CA41-103,189-266)M317D2 (S/N: CA61-284)M320D2 (S/N: EN81-330; CH91-149)M322D 2 MH (S/N: EN9215-215)M322D2 (S/N: EN21-207)M324D 2 MH (S/N: EN31-179)Description Of Change: A new injector sleeve has been introduced. The new injector sleeve has improved sealing bead geometry.Adaptable To: New 517-8243 Injector Sleeve replaces 277-5067 Injector Sleeve.To remove the existing injector sleeve, refer to Disassembly and Assembly, Fuel Injection Lines - Remove for the correct procedure.To install the new injector sleeve, refer to Disassembly and Assembly, Fuel Injection Lines - Install for the correct procedure.

Have questions with 101331-9210?





Group cross 101331-9210 ZEXEL

Nissan-Diesel 

 
16713L3400 
INJECTION-PUMP ASSEMBLY
SD15T
101331-9210  
9 400 613 525 
1671316H00 
INJECTION-PUMP ASSEMBLY
SD15T
Back to top