104661-0002 ZEXEL 9 461 629 177 BOSCH FUEL-INJECTION PUMP 9461629177 1046610002


 

Information fuel-injection pump

BOSCH 9 461 629 177 9461629177
ZEXEL 104661-0002 1046610002
104661-0002 FUEL-INJECTION PUMP
Rating:
58
Buy FUEL-INJECTION PUMP 104661-0002 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104761-0002 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104661-0002 
104661-0003 
9 461 629 177 
NP-VE6/11F1800RNP4 
   
FUEL-INJECTION PUMP
Q




Information:

3. Remove elbow (1) and fan drive lubricant tube (2).4. Loosen the clamps on hose (7), and move the hose down from cover (5).5. Disconnect cab heater return hose (6) at the valve.6. Mark the location of coolant conditioner hoses (3) and (4), and disconnect them at the fittings. 7. Remove O-ring seal (13) from elbow (11).8. Remove elbow (11) and tube (9).9. Disconnect cab heater supply valve (10) at the fitting.10. Remove four bolts (12) that hold the water pump to the bonnet. Remove O-ring seal (8) from the water pump. 11. Remove four nuts (15) and one bolt that hold water pump (14) to the timing gear housing.12. Remove the water pump and O-ring seal. The following steps are for installation of the water pump.13. Be sure the mating surface of the water pump and timing gear housing is clean.14. Be sure the mating surface of the water pump and bonnet is clean.15. Install a new O-ring seal on water pump (14).16. Install a new gasket between the water pump and the bonnet while installing the water pump on the timing gear housing.17. Install the four nuts and one bolt that hold water pump (14) to the timing gear housing.18. Install four bolts (12) that hold the water pump to the bonnet.19. Connect cab heater supply valve (10) to the fitting.20. Put clean glycerin on the O-ring seals, and install elbow (11) and tube (9). Install a new O-ring seal (13) in the elbow.21. Connect the coolant condition hoses (3) and (4) to the fittings. Connect the hoses in their original location.22. Connect cab heater return hose (6) to the valve.23. Move hose (7) into position on cover (5), and tighten the hose clamps.24. Install elbow (1) with new gaskets, and install fan drive lubricant tube (2).25. Fill the cooling system with coolant to the correct level. See the Maintenance Guide.Disassemble Water Pump
Start By:a. remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and the washer. 4. Remove impeller (4) from the water pump housing with Tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with Tooling (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and the bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove the lip-type seal from the gear side of the water pump. Remove the ring and seal from the impeller side of the water pump.13. Use 6V-1541 Quick Cure Primer to clean shaft (10) and the seal counterbore

Have questions with 104661-0002?





Group cross 104661-0002 ZEXEL

104661-0002  

104661-0003 
9 461 629 177 
NP-VE6/11F1800RNP4 
 
FUEL-INJECTION PUMP
9 461 618 289 
NP-VE6/11F1800RNP4 
 
FUEL-INJECTION PUMP
9 461 620 722 
NP-VE6/11F1200RNP5 
 
FUEL-INJECTION PUMP
9 461 615 252 
 
FUEL-INJECTION PUMP
9 461 620 547 
NP-VE6/11F1100RNP13 
 
FUEL-INJECTION PUMP
9 461 628 109 
 
FUEL-INJECTION PUMP
9 461 625 577 
 
FUEL-INJECTION PUMP
9 461 621 813 
 
FUEL-INJECTION PUMP
9 461 628 105 
 
FUEL-INJECTION PUMP
9 461 620 548 
NP-VE6/11F1200RNP488 
 
FUEL-INJECTION PUMP
Back to top