101801-6260 ZEXEL Calibration Data 1018016260 3126173011

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy None 101801-6260 zexel genuine, new aftermarket engine parts with delivery

Information

ZEXEL 101801-6260 1018016260

MITSUBISHI 3126173011 3126173011

Service parts 101801-6260 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101080-0450

3. GOVERNOR

4. SUPPLY PUMP 105210-4150

5. AUTOM. ADVANCE MECHANIS 105614-4040

6. COUPLING PLATE 105662-0470

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-4320

11. Nozzle and Holder 31261-69053

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105031-4230

14. NOZZLE 105015-3830

15. NOZZLE SET

Include in #1:

101801-6260 as INJECTION-PUMP ASSEMBLY

106871-2820 as _

Cross reference number

ZEXEL 101801-6260 1018016260

MITSUBISHI 3126173011 3126173011

Zexel num

Bosch num

Firm num

Name

101801-6260
101801-6950

3126173011 MITSUBISHI

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle 105015-3250

Bosch type code DLLA160S354NP49

Nozzle holder 105030-4030

Opening pressure MPa 21.6

Opening pressure kgf/cm2 220

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-700

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-3- 4-5-6-8

Pre-stroke mm 4.5 4.45 4.55

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-3 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cal 1-8 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 10.2

Pump speed r/min 1200 1200 1200

Average injection quantity mm3/st. 113 108.8 117.2

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 10.2

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 115 112.7 117.3

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 8.2+-0.5

Pump speed r/min 200 200 200

Average injection quantity mm3/st. 17.5 14 21

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_04

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 144 144

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 500+120- 100

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 800

Advance angle deg. 1.5 1 2

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 3.2 2.7 3.7

Timer adjustment_04

Pump speed r/min 1250

Advance angle deg. 6.5 6.5 7.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Set using excess fuel device for starting: SXL
----------
DL=5.5-0.2mm SXL=10.2+0.2mm
----------

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=5.5deg+-5deg b=26.5deg+-3deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+10r/min Ra=8.2mm
----------