09250-00103 COUPLING ASSY Denso Cross


 

Information coupling assy

09250-00103 COUPLING ASSY
Rating:
6
Buy COUPLING ASSY 09250-00103 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09250-00103 COUPLING ASSY 30061-60503
001. [01] 09255-10160 BLOCK, COUPLING 09255-10160
002. [01] 09241-50380 FLANGE, COUPLING 09241-50380
003. [01] 09243-70040 COUPLING, CROSS
004. [08] 09243-90050 PLATE, COUPLING 09243-90050
005. [08] 09246-10021 BUSHING, COUPLING 09246-10020
006. [08] 09246-20010 PLATE, COUPLING PL 09246-20010
007. [08] 94904-00591 BOLT, HEXAGON 94904-00591
008. [08] 90196-08651 NUT, HEXAGON ME728625
009. [08] 90258-08001 WASHER, SPRING MB239626
010. [02] 09241-70010 WASHER, COUPLING S ME703613
011. [01] 94904-80110 BOLT, WASHER HEAD

Cross reference number



Part num Firm num Firm Name
09250-00103  30061-6050  COUPLING ASSY




Information:

Removing:
6-1Cut through the starter gear ring with a hard chisel and remove.Fig. 6-1Refitting:
1. Heat the starter gear ring to a temperature of 120 deg. C. Place the starter gear ring with the bevelled side of the teeth facing away from flywheel.
6-22. Locate the starter gear ring on the flywheel and tap it into position so that it seats against the shoulder.Fig. 6-2Removing And Fitting A Radial Sealing Ring On The Flywheel Side
It is assumed that the flywheel has been dismantled. Removing:
6-3Apply puller No. 142700 and draw off radial sealing ring.Fig. 6-3Refitting:
6-41. Mount guide-piece of device onto crankshaft.Fig. 6-4
6-52. Lightly grease the sealing lip of the new radial seal. Place seal on guide-piece with lip facing towards crankcase and press in with device No. 142530.Fig. 6-5 Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the complete cover by adding gaskets accordingly.Dismantling, Installing And Sealing The Cover On The Flywheel Side (As from 3-cylinder engine)
The flywheel has already been removed.Dismantling:
1. Remove the bolts in the oil sump securing the cover on the flywheel side and the bolts securing the cover to the crankcase. Remove cover and gasket. Renew radial sealing ring. Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the latter in the cover.Installing:
6-112. Adhere new gasket to crankcase. Trim off the portion of gasket projecting beyond the joint surface of the sump. Fig. 6-113. Apply coat of Deutz DW 48 jointing compound to the oil sump gasket in the region of the cover.
6-124. Press new radial seal into the rear cover so that the outside surface is flush (arrow).Fig. 6-12 Prior to fitting, heat cover "hand-warm" and coat radial seal with jointing compound.
6-135. Place cover in position. Lightly pretighten cover bolts in crankcase. Fully tighten sump bolts in cover, then fully tighten bolts in crankcase.Fig. 6-13Exploded Views

Have questions with 09250-00103?





Group cross 09250-00103

Back to top