108622-3141 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1086223141


108622-3141 INJECTION-PUMP ASSEMBLY
Rating:
68
Buy INJECTION-PUMP ASSEMBLY 108622-3141 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 108622-3141 1086223141

Cross reference number

ZEXEL 108622-3141 1086223141


Zexel num
Bosch num
Firm num
Name
108622-3141 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-1520
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   21
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   6.4 6.37 6.43
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   A
Rack position   10.8
Pump speed r/min   550 550 550
Average injection quantity mm3/st.   193.4 191.4 195.4
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Boost pressure kPa   64 64
Boost pressure mmHg   480 480
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_02
Adjusting point   B
Rack position   10.2
Pump speed r/min   1050 1050 1050
Average injection quantity mm3/st.   168.6 165.6 171.6
Fixing the lever   *
Boost pressure kPa   64 64
Boost pressure mmHg   480 480
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Injection quantity adjustment_03
Adjusting point   C
Rack position   9.05
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   138.2 135.2 141.2
Fixing the lever   *
Boost pressure kPa   64 64
Boost pressure mmHg   480 480
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Injection quantity adjustment_04
Adjusting point   D
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   220 215 225
Fixing the lever   *
Boost pressure kPa   64 64
Boost pressure mmHg   480 480
Rack limit   *
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Injection quantity adjustment_05
Adjusting point   E
Rack position   4+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   12.5 9.5 15.5
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Injection quantity adjustment_06
Adjusting point   G
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   129 129 169
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Injection quantity adjustment_07
Adjusting point   H
Rack position   10.8+-0. 5
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   192.1 186.1 198.1
Fixing the lever   *
Boost pressure kPa   64 64
Boost pressure mmHg   480 480
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Boost compensator adjustment
Pump speed r/min   550 550 550
Rack position   8.15
Boost pressure kPa   22 20 22
Boost pressure mmHg   165 150 165
Boost compensator adjustment_02
Pump speed r/min   550 550 550
Rack position   10.8
Boost pressure kPa   50.7 50.7 50.7
Boost pressure mmHg   380 380 380
0000001601
Pre-stroke mm   6.4 6.37 6.43
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   5 4.5 5.5
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   4 3.95 4.05
Output voltage V   2.62 2.61 2.63
Adjustment   *
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   6.4 6.37 6.43
Output voltage V   1.2 0.7 1.7
Confirmation   *
Remarks
Output voltage V1
 
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   3.4
Output voltage V   3 2.98 3
Confirmation   *
_06
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Governor adjustment

Test data 108622-3141
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Stop lever setting: R1 (3)RACK LIMIT (4)Boost compensator stroke: BCL (5)Damper spring setting
----------
R1=12.4+0.2mm BCL=2.65+-0.1mm
----------

Speed control lever angle

Test data 108622-3141
F:Full speed
----------

----------
a=11deg+-5deg

0000000901

Test data 108622-3141
F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=91mm
----------
a=25deg+-5deg b=39.5deg+-3deg

Stop lever angle

Test data 108622-3141
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper screw at rack position = bb before governor adjustment. (After setting, apply red paint.) (3)-
----------
aa=33mm bb=12.4+0.2mm
----------
a=30deg+-5deg b=42deg+-5deg

0000001301

Test data 108622-3141
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=6.4+-0.03mm
----------
a=(40deg)

0000001901

Test data 108622-3141
(A): Pre-stroke actuator (B): Stamp housings A and B at the same time. (C): Stamping range 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully clockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the counterclockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

Test data 108622-3141
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump Adjustment of the rack sensor (-0720) 1. Rack limit adjustment (1)After mounting the joint (B), select the shim (D) so that the rack position is in the rack limit position. (2)Install the rod (E) to the block (C). (3)At the rack limit, set the distance between the pump end face and the rod (E) to L1. 2. Rack sensor (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the speed control lever at the full side and set the pump speed at N1. (3)Adjust the depth that the bobbin (A) is screwed in so that the control unit's rack sensor output voltage is VR+-0.01 (V), then tighten the nut (F). (If equipped with a boost compensator, perform with boost pressure applied.) (4)Apply red paint to both the joint (B) and the nut (F) join, and the joint (B) and the pump join. Output voltage VR +-0.01(V), speed N1, rack position Ra, rack sensor supply voltage 5+-0.01 (V)
----------
L=33.5+-0.1mm N1=550r/min Ra=10.8mm
----------




Have questions with 108622-3141?





Group cross 108622-3141 ZEXEL

Hino 

 
220007562A 
INJECTION-PUMP ASSEMBLY
P-4
 
220007563A 
INJECTION-PUMP ASSEMBLY
P-4
9 400 611 126 
220007565A 
INJECTION-PUMP ASSEMBLY
P-4
F 01G 09U 0E9 
220007566A 
INJECTION-PUMP ASSEMBLY
P-4
9 400 619 159 
220007567A 
INJECTION-PUMP ASSEMBLY
P-4
 
220007631A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 612 900 
220007632A 
INJECTION-PUMP ASSEMBLY
K-3
 
220007633A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 612 901 
220007633B 
INJECTION-PUMP ASSEMBLY
K-3
9 400 612 902 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 612 903 
220007634A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 612 904 
220007635A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 612 905 
220007635B 
INJECTION-PUMP ASSEMBLY
K-3
9 400 619 818 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 01G 09U 0EA 
220007636A 
INJECTION-PUMP ASSEMBLY
K-3
 
220007641A 
INJECTION-PUMP ASSEMBLY
K-4
9 400 612 906 
220007642A 
INJECTION-PUMP ASSEMBLY
K-4
 
220007643A 
INJECTION-PUMP ASSEMBLY
K-4
9 400 612 907 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 612 908 
220007643B 
INJECTION-PUMP ASSEMBLY
K-4
9 400 619 743 
220007644A 
INJECTION-PUMP ASSEMBLY
K-4
F 019 Z10 228 
220007644B 
INJECTION-PUMP ASSEMBLY
K-4
F 019 Z10 229 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 019 Z20 502 
220007645A 
INJECTION-PUMP ASSEMBLY
K-4
9 400 619 160 
220007646A 
INJECTION-PUMP ASSEMBLY
K-4
 
220007940A 
INJECTION-PUMP ASSEMBLY
P-3
9 400 612 909 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 619 161 
220007941A 
INJECTION-PUMP ASSEMBLY
P-3
 
220007950A 
INJECTION-PUMP ASSEMBLY
P-4
108622-3141  
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 619 162 
220007951A 
INJECTION-PUMP ASSEMBLY
P-4
 
220008050A 
INJECTION-PUMP ASSEMBLY
K13D
9 400 619 819 
220008051A 
INJECTION-PUMP ASSEMBLY
K13D
 
220008051B 
INJECTION-PUMP ASSEMBLY
K13D
9 400 619 163 
220008051C 
INJECTION-PUMP ASSEMBLY
K13D
 
220008170A 
INJECTION-PUMP ASSEMBLY
K-3
 
220008171A 
INJECTION-PUMP ASSEMBLY
K-3
 
220008171B 
INJECTION-PUMP ASSEMBLY
K-3
 
220008171C 
INJECTION-PUMP ASSEMBLY
K-3
9 400 619 628 
220008171D 
INJECTION-PUMP ASSEMBLY
K-3
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008171E 
INJECTION-PUMP ASSEMBLY
K-3
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008172B 
INJECTION-PUMP ASSEMBLY
K-3
9 400 611 567 
220008172C 
INJECTION-PUMP ASSEMBLY
K-3
 
220008210A 
INJECTION-PUMP ASSEMBLY
K-3
 
220008211A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 619 744 
220008212A 
INJECTION-PUMP ASSEMBLY
K-3
 
220008212B 
INJECTION-PUMP ASSEMBLY
K-3
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008213A 
INJECTION-PUMP ASSEMBLY
K-3
9 400 619 164 
220008213B 
INJECTION-PUMP ASSEMBLY
K-3
 
220008230A 
INJECTION-PUMP ASSEMBLY
P-3
 
220008231A 
INJECTION-PUMP ASSEMBLY
P-3
 
220008231B 
INJECTION-PUMP ASSEMBLY
P-3
F 01G 09U 0EB 
220008232A 
INJECTION-PUMP ASSEMBLY
P-3
F 01G 09U 0EC 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 01G 09U 0ED 
220008233A 
INJECTION-PUMP ASSEMBLY
P-3
F 01G 09U 0EE 
220008234A 
INJECTION-PUMP ASSEMBLY
P-3
9 400 619 165 
220008235A 
INJECTION-PUMP ASSEMBLY
P-3
 
220008240A 
INJECTION-PUMP ASSEMBLY
P-4
 
220008241A 
INJECTION-PUMP ASSEMBLY
P-4
 
220008241B 
INJECTION-PUMP ASSEMBLY
P-4
 
220008242A 
INJECTION-PUMP ASSEMBLY
P-4
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008243A 
INJECTION-PUMP ASSEMBLY
P-4
 
220008244A 
INJECTION-PUMP ASSEMBLY
P-4
9 400 619 166 
220008245A 
INJECTION-PUMP ASSEMBLY
P-4
Back to top